Skip to main content
Error code reference
Jenn-Air Range Error Codes
83 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
1c1cShorted key detected on the keyboard.1c2cKeyboard disconnected from the control.1c4cBoard-to-board communication failure between display and relay boards.1c6cEEPROM hardware fault detected during EEPROM access.1c7cControl not calibrated; detected during programming, cook, or clean mode.1c81EEPROM CRC error in upper cavity cook profile data.1c8cEEPROM CRC error in user options data.1d11Unlocked runaway temperature condition detected (temperature exceeds 600°F with latch not…1d21Locked runaway temperature condition detected (temperature exceeds 950°F with latch…3d11Oven temperature sensor open circuit detected during active cook or clean mode.3d21Oven temperature sensor shorted during active cook or clean mode.3d41Meat probe shorted during active probe cook mode.3d51Meat probe not calibrated; detected during active probe cook mode.4d11Door switch not closed when door latch is in the locked position.4d21No cooling fan rotation detected during active cook or clean mode.4d31Cooling fan is running when it should be de-energized (cooling fan on when idle).4d41Cooling fan overspeed condition detected during active cook or clean mode.4d51Door switch circuit fault detected during active clean, convection, or control lockout…9d11Door latch will not lock when it should be in locked position.9d21Door latch will not unlock when it should be in unlocked position.9d31Door latch indicates both locked and unlocked states simultaneously.BAKEFlashing BAKE in the display indicates an electronic control error or problem requiring…FA fault code displayed as 'F' plus a number indicates a system fault requiring service…F0-0No fault present.F0E0No error(s) foundF1Element relay circuitF1-1Oven temperature above 650°F (343°C) in bake mode.F1-3Oven temperature above 950°F (510°C) during a clean cycle.F1-5Cancel pad not responding.F1-7Membrane disconnected.F1-8Shorted key (pad) in membrane switch.F1-9Internal control communication errors.F1-ALock/unlock switch state not advancing to control.F1-COven door switch state not advancing to control.F1-EControl not calibrated.F1-FJumper not removed from printed circuit board (PCB).F1-HEEPROM error.F1-NInternal voltage for slave micro incorrect.F1E0User Interface Board EEPROM Communication ErrorF1E1Control Relay Board EEPROM Communication ErrorF2Excessive cavity temperatureF2E0Keypad disconnected.F2E1Stuck KeyF2E2Oven Knob Rotary Encoder Open/ShortedF2E3Keypad hardware failure.F3Oven temperature sensorF3-1Open or shorted oven temperature sensor.F3E0Main Oven Sensor Open or ShortedF3E1Left Oven Sensor Open or ShortedF3E2Warming drawer sensor shortedF3E3Main Oven Meat Probe Short-CircuitF3E9Left Oven Meat Probe Short-CircuitF4Oven temperature sensorF5Shorted temperature probe, jack or harness.F5E0Main Oven Door Latch SwitchF5E1Main Oven Door Latch MotorF5E3Left Oven Door Latch SwitchF5E4Left Oven Door Latch MotorF6Main control board shorted (only time of day and minute timer will work).F6E0User Interface Connection LostF6E1Main Oven Over Temperature LimitF6E2Clean oven over temperature.F6E3Left Oven Over Temperature LimitF6E4Control StatusF6E5Cavity size is incorrect.F6E6Main Oven Control ConnectionF6E9Left Oven Control ConnectionF7Clean/lock switch assembly shorted or open, or lock motor still runs.F7E1Boiler Over Temperature Limit (steam models)F7E2Boiler Temperature Out of Range (steam models)F8Door lock motor inoperative or open wiring to motor.F8E0Main Oven Cooling Fan speed low or not functioningF8E1Left Oven Cooling Fan Speed LowF8E2Main Oven Cooling Fan Speed HighF8E3Left Oven Cooling Fan Speed HighF9-1Oven door will not lock.F9-2Oven door will not unlock.F9-3Oven door status is both locked and unlocked.F9E0Power InputFAULT DETECTEDThe oven has detected a fault during programming or during operation.FEATURE NOT AVAILABLEThe same operation was attempted before having the oven repaired after a fault was…LOCKFlashing LOCK in the display indicates an electronic control error or problem requiring…SAbOven is in Sabbath Mode and the display shows SAb flashing then displayed continuously.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Jenn-Air error codes
Common questions
How do I find the error code on my Jenn-Air Range?
Most Jenn-Air ranges show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Jenn-Air ranges. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.