mypros+
Error code reference

KitchenAid Cooktop Error Code F-61

Power control board does not work (Type 2).

KitchenAid codesKitchenAid cooktop codes

Power control board does not work (Type 2).

First step from the service manual

Disconnect power and check that the cables between the User Interface and the power control board are not damaged and are firmly plugged in.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F-61.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F-61 means on a KitchenAid cooktop

The F-61 error code on a KitchenAid cooktop indicates a Type 2 power control board fault. The power control board is the primary electrical component responsible for managing power distribution to the heating elements and coordinating signals with the user interface board. When the control system detects that the power control board is not functioning within expected parameters, it triggers this fault code to prevent unsafe operation of the cooktop.

The most common entry point for diagnosing this fault is the communication and power wiring between the user interface board and the power control board. Loose connectors, pinched wiring harnesses, or cables that have experienced heat damage over time can all disrupt the signal between these two boards, causing the cooktop to register a board failure even when the board itself may still be intact. This is why the first diagnostic step focuses on inspecting and reseating these connections before condemning the board.

If the wiring and connectors are found to be in good condition and properly seated, the fault points toward an internal failure of the power control board itself. Board failures can result from component-level damage such as failed relays, burned traces, or degraded capacitors, often caused by power surges, overheating, or simple end-of-life wear. In these cases, replacement of the power control board is typically required to restore normal cooktop operation.

Source: manufacturer service documentation.

Common causes of F-61

  1. 01

    Loose or disconnected wiring harness

    Wiring / connection

    The cable connecting the user interface board to the power control board may have come loose or worked itself out of its connector. Disconnecting power and firmly reseating both ends of this harness is the first step and sometimes resolves the fault entirely.

  2. 02

    Damaged wiring between boards

    Part replacement

    Heat exposure or physical pinching can fray or break wires in the harness running between the two control boards. Inspect the full length of the cable for burn marks, melted insulation, or visible breaks.

  3. 03

    Failed power control board

    Part replacement

    If wiring checks out, the power control board itself may have an internal failure such as a burned relay or damaged circuit. This is a common outcome after power surges or prolonged use and requires board replacement.

  4. 04

    Failed user interface board

    Part replacement

    In some cases, the user interface board sends an incorrect or absent signal that causes the system to flag a power control board fault. If the power control board tests as functional, the user interface board should be evaluated as well.

  5. 05

    Power surge or transient voltage event

    Wiring / connection

    A sudden spike in incoming power can trigger fault codes or cause lasting damage to control board components. If the fault appeared immediately after a storm or power interruption, this is a likely contributing factor.

See the test procedure for each cause

Frequently asked questions about F-61

What does F-61 mean on a KitchenAid cooktop?
F-61 is a Type 2 power control board fault on a KitchenAid cooktop. It means the cooktop's control system has detected that the power control board is not operating correctly. The cooktop will stop working until the fault is diagnosed and resolved. The issue can stem from wiring problems between the boards or an actual failure of the power control board itself.
Will resetting the cooktop clear the F-61 error code?
Disconnecting power to the cooktop for several minutes and restoring it may temporarily clear the F-61 code, but if an underlying problem exists, the code will return. A reset is useful for ruling out a one-time electrical glitch, but persistent F-61 faults require physical inspection of the wiring and control boards to identify the root cause.
Can I fix the F-61 error on my KitchenAid cooktop myself?
A knowledgeable DIYer can start by disconnecting power and checking that all wiring harnesses between the user interface board and the power control board are intact and firmly connected. If the cables look good and the fault persists, replacing the power control board is typically the next step. Working inside a cooktop involves exposure to high-voltage components, so proper precautions and confirmed power disconnection are essential before beginning any inspection.
Is it safe to use my KitchenAid cooktop while the F-61 code is showing?
No. The F-61 code indicates the power control board is not functioning properly, and the cooktop should not be used until the fault is corrected. Attempting to operate the cooktop in this condition could result in unpredictable behavior from the heating elements or further damage to the control electronics.
How much does it cost to fix a KitchenAid cooktop F-61 error?
If the fault is caused only by a loose wiring connection, the repair may cost nothing beyond your time. If the power control board needs to be replaced, parts typically range from $150 to $400 or more depending on the specific cooktop model, with additional labor costs if a technician performs the repair. Obtaining a parts quote for your specific model number before committing to a repair is a good way to assess whether the repair cost is justified.

Related KitchenAid cooktop codes

All KitchenAid cooktop codes
View all 38 KitchenAid cooktop codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass