mypros+
Error code reference

Maytag Dishwasher Error Code F4-E3

Wash motor not running due to loose connection in motor circuit and/or faulty wash motor, or control motor drive/sense circuit failure.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F4-E3 error code actually means

The F4-E3 code means your dishwasher's main wash motor, the part that pumps water through the spray arms, is not running during a cycle. This could be caused by a loose wire, a faulty motor, or a problem with the control board. Until the issue is fixed, the dishwasher will not be able to clean dishes.

Diagnostic procedure

The full F4-E3 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check operation of wash motor during diagnostics. Unplug dishwasher, check resistances of connections in the wash circuit. If high resistance, check/fix loose connections or replace wash motor.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F4-E3 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F4-E3

Ranked by how often they cause this code
  1. 1Loose or high-resistance wiring connections
  2. 2Faulty wash motor
  3. 3Control board motor drive or sense circuit failure
  4. 4Open circuit in wash motor wiring harness

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F4-E3

What does F4-E3 mean on a Maytag dishwasher?
F4-E3 indicates that the wash motor is not running during a cycle. The control board monitors the motor circuit and trips this fault when it detects no motor activity or a problem in the drive and sense circuitry. The cause can be a loose connection in the motor circuit, a failed wash motor, or a control board failure. The dishwasher will not complete a wash cycle until the issue is resolved.
Is it safe to run my dishwasher with an F4-E3 error?
You should not attempt to run the dishwasher while this fault is active. Because the wash motor is not operating, the appliance cannot complete its cycle and will leave dishes uncleaned. Repeatedly attempting to start cycles without addressing the underlying fault will not cause immediate danger but does not resolve the problem and could mask worsening electrical issues.
Will resetting the dishwasher clear the F4-E3 error code?
A reset may temporarily clear the fault code from the display, but the error will return if the underlying problem has not been fixed. The F4-E3 code is triggered by an active condition in the wash motor circuit, so the control board will detect the same fault again the next time a wash cycle is attempted. Proper diagnosis and repair of the motor circuit or control board is required for a lasting fix.
Can I fix the F4-E3 error myself?
Some causes of F4-E3 are DIY-friendly. After unplugging the dishwasher, you can inspect and reseat all wiring connections in the wash motor circuit, which sometimes resolves the fault if a loose connector is the culprit. If connections are secure and the motor needs replacement, that repair is more involved but manageable for experienced DIYers. A failed control board is typically the most complex repair and may warrant professional service.
How much does it cost to repair the F4-E3 error on a Maytag dishwasher?
Repair costs depend on the root cause. If the fix is simply reseating a loose connector, there may be no parts cost, only labor if a technician is involved. A replacement wash motor typically falls in the range of $100 to $250 for parts, with additional labor costs if professionally installed. A control board replacement can range from $150 to $350 or more for parts alone, making it the most expensive potential outcome.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass