mypros+
Error code reference

Samsung Refrigerator Error Code Ice Room Sensor

Ice room sensor error

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Ice Room Sensor error code actually means

Your Samsung refrigerator is showing an error because the sensor that monitors the temperature inside the ice maker compartment is sending a reading that is impossibly high or low. This usually means the sensor itself has failed or a wire connecting it to the control board has come loose or broken. The ice maker may stop working properly until this is resolved.

Diagnostic procedure

The full Ice Room Sensor procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check voltage at MAIN PCB CN78-10 to CN78-1 is between 4.5V and 1.0V.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Ice Room Sensor procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Ice Room Sensor

Ranked by how often they cause this code
  1. 1Faulty ice room thermistor
  2. 2Damaged or broken wiring harness
  3. 3Corroded or loose connector at CN78
  4. 4Ice or frost buildup blocking or damaging the sensor
  5. 5Main PCB sensing circuit fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Ice Room Sensor

What does Ice Room Sensor mean on a Samsung refrigerator?
The Ice Room Sensor error means the control board is receiving a temperature reading from the ice compartment sensor that falls outside the valid range, specifically above 149°F (65°C) or below -58°F (-50°C). Because these temperatures are not physically possible inside an ice room under normal use, the error indicates a sensor failure, wiring fault, or connector problem rather than an actual temperature issue. The ice maker function is typically disrupted until the fault is corrected.
Is it safe to keep using my refrigerator while the Ice Room Sensor error is active?
The refrigerator's main fresh food and freezer compartments will generally continue operating normally because they use separate sensors and controls. However, the ice maker may stop producing ice or behave erratically. It is best to address the error promptly to avoid any secondary issues related to ice maker operation, such as water leaks from a stuck cycle.
How much does it cost to repair the Ice Room Sensor error on a Samsung refrigerator?
If the thermistor is the failed component, the part itself is generally inexpensive, typically in the range of $15 to $40, and the repair is straightforward. If professional labor is required, expect to add $80 to $150 for a service call and diagnosis. A Main PCB replacement is significantly more expensive, with parts and labor potentially totaling $200 to $450 depending on the model and service provider.
Can I fix the Ice Room Sensor error myself?
A knowledgeable DIYer can handle several of the likely causes. Start by checking the connector at CN78 on the Main PCB for looseness or corrosion and reseat it if needed. If the connector is fine, use a multimeter to test the voltage at CN78-10 to CN78-1 and check the thermistor's resistance directly. Replacing a thermistor is a straightforward repair, but if the Main PCB itself is faulty, professional service is recommended.
Will resetting my Samsung refrigerator clear the Ice Room Sensor error?
A power reset may temporarily clear the error code from the display, but the fault will return if the underlying hardware problem has not been repaired. Resetting does not fix a failed thermistor, broken wire, or faulty connector. Use a reset only to confirm whether a transient electrical event caused the code, not as a long-term solution.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass