mypros+
Model reference

AEG EWM2000EVONEW

Washer

1 document69 error codes5 service modes

Available documentation

Service Manual

  • Service Manual Waschen49 pg
    Covers this model
MyPros+ Max

Diagnose your AEG EWM2000EVONEW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (69)

CodeMeaning
E10No water inletE11No water inlet (same as E10).E13Too little waterE20No water drainE21No water drain (same as E20).E23Incongruence between pump and electronics.E24Measuring circuit for pump triac always 0V or 5V.E30Pressure sensor defectiveE31Pressure sensor defectiveE32Calibration error of pressure sensorE33Incongruence between pressure sensor and dry run protection 1 (error must…E34Incongruence between pressure sensor and dry run protection 2E35Safety levelE36Measuring circuit for dry run protection 1 always 0V.E37Measuring circuit for dry run protection 2 always 0V or 5V; also measuring…E38Air trap blockedE39Measuring circuit HV pressure switch level 1 always 0V.E3AHeating relay defective.E40Lid open.E41Lid open (same as E40).E42Door interlock defectiveE43Triac for door interlock defective.E44Measuring circuit for door interlock always 0V or 5V.E45Measuring circuit for door interlock triac always 0V or 5V.E50Motor triac short circuit.E51Motor ribbon cable short circuit.E52Tachogenerator interrupted or motor blocked.E53Measuring circuit for motor triac always 0V or 5V.E54Motor relay defective.E55Motor circuit interrupted.
View all 69 error codes
E56Tachogenerator interruptedE60Does not heatE61Does not heatE62OverheatingE66Heating relay defectiveE70NTC short circuit or NTC interrupted.E71NTC short circuit or NTC interrupted (same as E70).E74NTC is not in the correct installation position.E80Faulty reset position of the program selector.E82Faulty reset position of the program selector (same as E80).E83Read error of the program selectorE84Measuring circuit for circulation pump always 0V or 5V.E85Circulation pump defective or triac defective.E90Communication between I/O electronics and main electronics interrupted.E91Communication between I/O electronics and main electronics interrupted (same as…E92Incongruence between I/O electronics and main electronicsE93Configuration errorE94Faulty configuration of the wash programE95Communication error between microprocessor and EEPROM.E96Missing correspondence between hardware version and configuration.E97Missing correspondence between program selector and program configuration.EA0DSP (Drum Self Position) defective.EA1DSP defective (same as EA0).EA2DSP signals defective.EA3DSP cannot block the motor pulley.EA4DSP defective.EA5Triac for DSP defective.EA6Drum blocked in the first approx. 30 secondsEB0Mains frequency outside limit values.EB1Mains frequency outside limit values (same as EB0).EB2Mains voltage too high.EB3Mains voltage too low.EC0Inlet valve blocked.EC1Inlet valve blocked (same as EC0).EC2Turbidity sensor defective.EF0Lint filter clogged or drain hose cloggedEF1Lint filter clogged or drain hose cloggedEF2OverdosingEF3Aqua Control activated

Service modes (5)

  • Clear Last Error Code1
  • Demo Program1
  • Operating Hours Counter1
  • Quick Error Code ReadPress and hold Button 2 and Button 1 simultaneously during any operating mode (even during a wash…
  • Service Program (Diagnostic)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related AEG washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass