mypros+
Error code reference

AEG Washer Error Code E11

Too little water

AEG codesAEG washer codes

Too little water - drain hose incorrectly routed, insufficient flow rate, inlet valve defective, pressure switch defective, or leak/blockage in pressure switch hydraulic circuit.

First step from the service manual

Correctly route the drain hose.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E11.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E11 means on a AEG washer

The E11 error code on an AEG washer indicates that the machine detected insufficient water entering the drum during the fill phase. The control board monitors water level through a pressure switch, which senses drum fill level via a hydraulic circuit connected to an air chamber and pressure hose. When the expected water level is not reached within a set time window, E11 is triggered. This code does not always mean water is absent entirely, but rather that the fill rate or detected level did not meet the programmed threshold.

Several components are involved in this fault. The inlet valve controls the flow of water into the machine, and a defective or partially blocked valve can reduce flow to an unacceptable rate. The pressure switch and its associated hydraulic circuit, which includes a small rubber hose connecting the air trap to the switch, must maintain an airtight seal to accurately report water level. A leak, blockage, or kink in this hose can cause the switch to misread the actual water level, triggering E11 even when water is entering normally.

An incorrectly routed drain hose is the most common and easily overlooked cause. If the drain hose is positioned too low, it can create a siphoning effect that continuously drains water as it fills, preventing the drum from ever reaching the required level. The hose standpipe height must meet the installation specification to prevent this. After ruling out routing issues, checking water supply pressure, inspecting the inlet valve filter screens, and testing the pressure switch circuit are the recommended diagnostic steps.

Source: manufacturer service documentation.

Common causes of E11

  1. 01

    Drain hose incorrectly routed

    Wiring / connection

    If the drain hose is positioned too low or lacks sufficient height at the standpipe, a siphon effect pulls water out of the drum during filling. Verify the drain hose is routed and secured at the correct standpipe height per installation requirements.

  2. 02

    Restricted water inlet flow

    Wiring / connection

    Low household water pressure or clogged filter screens at the inlet valve connection can reduce flow rate below the required threshold. Inspect and clean the inlet hose filter screens and confirm adequate water supply pressure at the tap.

  3. 03

    Defective inlet valve

    Part replacement

    The solenoid inlet valve may be failing to open fully or at all, resulting in little or no water entering the drum. A valve that does not fully energize or has a damaged solenoid coil will need to be replaced.

  4. 04

    Pressure switch defective

    Part replacement

    The pressure switch translates drum water level into an electrical signal for the control board. A faulty switch may fail to signal that the fill threshold has been reached, causing the board to log E11 even with adequate water present.

  5. 05

    Leak or blockage in pressure switch hydraulic circuit

    Wiring / connection

    The small rubber hose connecting the drum air trap to the pressure switch must be airtight and clear. A crack, loose connection, kink, or blockage in this hose causes inaccurate water level readings and can trigger E11 falsely.

See the test procedure for each cause

Frequently asked questions about E11

What does E11 mean on a AEG washer?
E11 on an AEG washer means the machine detected too little water in the drum during the fill cycle. The control board monitors water level through a pressure switch, and when the required level is not reached in time, this code is triggered. Causes include an incorrectly routed drain hose, low water flow, a defective inlet valve, a faulty pressure switch, or a problem in the pressure switch hydraulic circuit.
How do I fix the E11 error on my AEG washer?
Start by checking that the drain hose is routed correctly and secured at the proper standpipe height, as a siphoning drain hose is the most common cause. Next, inspect the inlet hose filter screens for blockages and confirm the water supply tap is fully open. If those checks pass, the inlet valve or pressure switch may need to be tested and replaced.
Will resetting my AEG washer clear the E11 error?
A reset may clear the E11 code temporarily, but if the underlying cause has not been addressed, the error will return when the machine attempts another fill cycle. Resetting is useful for confirming whether a one-time fault occurred, but it is not a substitute for diagnosing and correcting the root cause.
Is it safe to use my AEG washer while E11 is showing?
It is not recommended to continue using the washer while E11 is active. The machine cannot complete a normal cycle without reaching the required water level, and repeated failed attempts could place stress on the motor and pump components. Resolve the fault before running further loads.
How much does it cost to repair an AEG washer showing E11?
If the issue is simply a misrouted drain hose, there is no parts cost involved. Replacing a faulty inlet valve typically costs between $40 and $120 for the part, while a pressure switch replacement generally ranges from $25 to $80, with additional labor costs if a technician is hired. The total repair cost depends on which component is at fault and whether you perform the repair yourself.

Related AEG washer codes

All AEG washer codes
View all 78 AEG washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass