mypros+
Error code reference

AEG Washer Error Codes

83 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.
C1Water inlet failureC2Drain failureC3Aqua-control system activatedC4Recirculation pump triac short circuit, interrupted recirculation pump, or recirculation…C5High temperature at motor detected.C6Pressure sensor defective, dry-run safety switch (TR1/TR2) defective, cable defective, or…C7Temperature not increasingC8NTC short circuit, NTC open circuit, or NTC cable break.C9Tachogenerator short circuit or open circuit, motor short circuit or open circuit, motor…CAMOS-FET transistor defective on motor (DC) electronics board.CbSafety level reached 5 times; valve mechanically defective.CCPTC for MOS-FET on motor electronics defective.CDDoor lock defective, wiring to door lock defective, or electronics defective.CFNo machine data or no program data found in main electronics.E10No water inletE11No water inlet (same as E10).E13Too little waterE20No water drainE21No water drain (same as E20).E23Incongruence between pump and electronics.E24Measuring circuit for pump triac always 0V or 5V.E30Pressure sensor defectiveE31Pressure sensor defectiveE32Calibration error of pressure sensorE33Incongruence between pressure sensor and dry run protection 1 (error must persist >60…E34Incongruence between pressure sensor and dry run protection 2E35Safety levelE36Measuring circuit for dry run protection 1 always 0V.E37Measuring circuit for dry run protection 2 always 0V or 5V; also measuring circuit…E38Air trap blockedE39Measuring circuit HV pressure switch level 1 always 0V.E3AHeating relay defective.E40Door lock problem (door not properly closed or locked).E41Lid open (same as E40).E42Door interlock defectiveE43Triac for door interlock defective.E44Measuring circuit for door interlock always 0V or 5V.E45Measuring circuit for door interlock triac always 0V or 5V.E50Motor triac short circuit.E51Motor ribbon cable short circuit.E52Tachogenerator interrupted or motor blocked.E53Measuring circuit for motor triac always 0V or 5V.E54Motor relay defective.E55Motor circuit interrupted.E56Tachogenerator interruptedE60Does not heatE61Does not heatE62OverheatingE66Heating relay defectiveE70NTC short circuit or NTC interrupted.E71NTC short circuit or NTC interrupted (same as E70).E74NTC is not in the correct installation position.E80Faulty reset position of the program selector.E82Faulty reset position of the program selector (same as E80).E83Read error of the program selectorE84Measuring circuit for circulation pump always 0V or 5V.E85Circulation pump defective or triac defective.E90Communication between I/O electronics and main electronics interrupted.E91Communication between I/O electronics and main electronics interrupted (same as E90).E92Incongruence between I/O electronics and main electronicsE93Configuration error (indicated by Prewash, Rinse+, End and Overdosed LEDs blinking).E94Faulty configuration of the wash programE95Communication error between microprocessor and EEPROM.E96Missing correspondence between hardware version and configuration.E97Missing correspondence between program selector and program configuration.EA0DSP (Drum Self Position) defective.EA1DSP defective (same as EA0).EA2DSP signals defective.EA3DSP cannot block the motor pulley.EA4DSP defective.EA5Triac for DSP defective.EA6Drum blocked in the first approx. 30 secondsEB0Mains frequency outside limit values.EB1Mains frequency outside limit values (same as EB0).EB2Mains voltage too high.EB3Mains voltage too low.EC0Inlet valve blocked.EC1Inlet valve blocked (same as EC0).EC2Turbidity sensor defective.EF0Aqua-Control float switch activated (water leak detected in base).EF1Lint filter clogged or drain hose cloggedEF2OverdosingEF3Aqua Control activated

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.