mypros+
Error code reference

AEG Washer Error Code E7

NTC short circuit, NTC open circuit, or NTC cable break.

AEG codesAEG washer codes

NTC short circuit, NTC open circuit, or NTC cable break.

First step from the service manual

Replace NTC; replace cable.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E7.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E7 means on a AEG washer

The E7 error code on an AEG washer indicates a fault with the NTC (Negative Temperature Coefficient) thermistor, which is the temperature sensor responsible for monitoring water temperature inside the drum or heating circuit. The NTC thermistor works by changing its electrical resistance in response to temperature changes. When the machine's control board reads a resistance value outside the expected range, it triggers the E7 fault. Three distinct conditions can cause this: a short circuit in the NTC (resistance too low), an open circuit in the NTC (resistance too high or infinite), or a physical break in the NTC cable that interrupts the signal entirely.

A shorted NTC will typically report an abnormally high or constant temperature reading, while an open circuit or cable break results in no temperature signal reaching the control board. In both cases, the washer cannot regulate heating safely and will halt the cycle to prevent overheating or malfunction. The NTC sensor itself is a relatively small, inexpensive component, but wiring harness damage from vibration, heat, or pinching during installation can produce identical fault symptoms.

Diagnosis should begin by inspecting the NTC cable and connector for visible damage, corrosion, or loose terminals. If the wiring appears intact, the NTC thermistor should be tested with a multimeter to confirm whether its resistance reading falls within the expected range for the ambient temperature. A reading of zero ohms indicates a short, while an open-loop reading indicates a failed sensor or broken circuit. Replacement of the NTC sensor or the associated cable is the recommended corrective action.

Source: manufacturer service documentation.

Common causes of E7

  1. 01

    Failed NTC thermistor

    Part replacement

    The NTC sensor itself has failed internally, resulting in either a short circuit or an open circuit. Testing with a multimeter will show either zero resistance or no continuity at all.

  2. 02

    Broken NTC cable

    Part replacement

    The wiring between the NTC sensor and the control board has developed a break, interrupting the temperature signal. Inspect the cable along its full length for visible cuts, pinching, or heat damage.

  3. 03

    Corroded or loose NTC connector

    Wiring / connection

    The connector at the NTC thermistor or control board end may have corroded pins or a loose fit, causing an intermittent or absent signal. Cleaning the terminals or reseating the connector may resolve the fault.

  4. 04

    Short circuit in the NTC wiring harness

    Part replacement

    Chafed or damaged insulation on the NTC wiring can cause adjacent wires to contact each other or a grounded surface, producing a short circuit reading at the control board.

See the test procedure for each cause

Frequently asked questions about E7

What does E7 mean on a AEG washer?
The E7 code on an AEG washer indicates a fault with the NTC thermistor, which is the water temperature sensor. The error is triggered when the control board detects a short circuit, open circuit, or cable break in the NTC circuit. Because the machine cannot safely monitor water temperature, it stops the cycle and displays E7 until the issue is resolved.
Can I fix the E7 error myself?
A knowledgeable DIYer can attempt to diagnose E7 by visually inspecting the NTC cable for damage and checking connector terminals for corrosion or looseness. If the wiring looks intact, testing the NTC thermistor with a multimeter will confirm whether it has failed. Replacing the NTC sensor is a relatively straightforward repair, but working near electrical components requires care and the machine should always be unplugged before beginning any inspection.
Is it safe to keep using my AEG washer with an E7 error?
It is not advisable to continue using the washer while E7 is active. Without a functioning temperature sensor, the machine cannot properly regulate water heating, which could lead to overheating or incomplete wash cycles. The washer will typically halt operation automatically when this fault is present, so continued use is generally not possible until the fault is cleared.
How much does it cost to repair an E7 error on an AEG washer?
If only the NTC thermistor needs replacement, the part itself is typically inexpensive, often in the range of $10 to $40 depending on the model. If a professional technician is needed, total repair costs including labor generally fall between $80 and $180. Wiring harness repairs can add to that range if cable damage is extensive.
Will resetting the washer clear the E7 error code?
Resetting the washer by unplugging it for a few minutes may temporarily clear the E7 display, but the fault will return as soon as the machine attempts to read the temperature sensor again. A reset does not fix the underlying hardware issue. Permanent resolution requires inspecting, testing, and replacing the NTC thermistor or its cable as needed.

Related AEG washer codes

All AEG washer codes
View all 78 AEG washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass