Model reference

Amana 11-2G

Air Conditioner

1 document40 error codes11 service modes

Available documentation

Other

  • 1602206142 pg
    Covers this model
MyPros+ Max

Diagnose your Amana 11-2G.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (40)

CodeMeaning
dc.1Blocked coin 1 or coin drop UI control circuit failure; coin recognition and…dc.2Voltage detected below 90 VAC for 8 seconds.dc.3Blocked coin 2 or coin drop UI control circuit failure; coin recognition and…dc.4Not receiving communications from installed debit card reader in Enhanced…dc.5Dryer motor control circuit error; cycles and price display disabled until…dc.6Exhaust thermistor open; temperature drops below 18°F (>50 kOhm) for 1 minute…dc.7Exhaust thermistor shorted; temperature above 250°F (<500 Ohm) for 1 minute in…dc.8UI is not receiving communications from CCU; cycles and price display disabled…dc.9CCU is not receiving communications from UI; cycles and price display disabled…dc.AUI Microprocessor is not able to read or verify EEPROM; cycles and price…dc.bUI EEPROM memory is a CRC failure; cycles and price display disabled until…F1E1Primary control failure.F2E1Stuck button or user interface mismatch (only appears in service diagnostic…F3E0Main sensor open (upper oven sensor circuit is open).F3E1RC (Refrigerator Compartment) sensor fault.F3E2FC (Freezer Compartment) sensor fault.F3E4Bottom sensor open (lower oven sensor circuit is open).F3E5Evaporator sensor fault.F3E6Warming drawer sensor open.F3E7Warming drawer sensor shorted.F3E8RH (Relative Humidity) sensor fault.F3E9Ambient temperature sensor fault.F3EbPantry sensor fault.F4E1Heater fault.F4E2Over temperature during cook mode.F4E3Over temperature during clean (self-clean) mode.F4E4Low line voltage detected.F4E7Over temperature in cavity 2.F5E0Door latch mismatch (mismatch between door switch and latch switch).F5E1Latch not operating (door latch motor is not functioning).
View all 40 error codes

Service modes (11)

  • Customer-Focused Drying Mode Adjustment["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the DRY…
  • diagnostic mode["Enter set-up mode first.","Navigate to set-up code 6 xx or 7 xx, or have a diagnostic code…
  • Error Code Access (Freeman/Mirror UI)["Hold RC + Cubed Ice buttons for 5 seconds (use Control Lock for NIDI models)."]
  • help mode["Enter set-up mode.","Navigate to special pricing option 2.XX.","Press the COTTON/WHITES button to…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the DRY…
  • Service Test Mode (Callisto-ACU)["Press and release any 3 keypad buttons, three times consecutively
  • set-up mode (9050 models with service key)["Insert service access door key, turn, and lift to remove service access door."]
  • set-up mode (9060 models without service key via AA1 connector)["Unplug dryer or disconnect power.","Open console, remove plug on AA1, close console.","Plug in…
  • set-up mode (via Service Access Code)["Press the Left Button, Right Button, Left Button, Right Button, Right Button."]
  • set-up mode (with card reader installed)["Insert a manual set-up card (supplied by the reader manufacturer) into the card slot."]
  • User Interface/Control System Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass