mypros+
Model reference

Amana 11-2J

Air Conditioner

43 error codes22 service modes
MyPros+ Max

Diagnose your Amana 11-2J.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
F0E0No fault detected.F0E2Wrong voltage detected.F0E3Long drain faultF0E4Water hazard condition detected.F0E5Overflow or flood condition detected.F0E7Long fillF0E8Motor drive module over current or overload condition.F0E9Motor phase loss detected.F1E1Locked rotorF1E2Motor drive module over temperature condition.F2E1Motor unable to reach target RPM.F2E2Motor circuit open.F2E3Basket re-engagement failure.F3E1Exhaust thermistor is open or shorted; open if temperature drops below 18°F…F3E2Basket engaged during wash.F3E3MCI drive failure.F3E5Second moisture sensor strip is open or shorted (only Quad Sense models; only…F5E1Tachometer missing or wrong signal.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Communication errorF5E4Communication errorF6E1Lid not opened between cycles.F6E2Communication between the ACU and HMI has not been detected.F6E3Lid will not lock or unlock.F7E1Lid switch faultF7E2Inlet water temperature fault.F7E3Pressure system fault.F7E4ACU/UI mismatchF7E5Shifter fault; main control cannot determine position of shifter.F7E6UI disconnected from main control.
View all 43 error codes
F7E7UI stuck button detected.F7E8Motor drive module over voltage.F7E9Main control (ACU) fault.F7EAOff balance pause condition detected.F7ECWater ring detected.F8E1Load detected when running Clean Washer cycle.F8E3Off balance load detected.F8E5Hot and cold water inlet hoses are reversed.F8E6Spin limited by water temperature.F9E1Overload condition detected.F9E9Oversuds condition detected.FCE1WIFI Module has not responded for a specified amount of time; communications…PFPower failure occurred while the dryer was running.

Service modes (22)

  • Automatic Test["From Service Mode, rotate E3 in clockwise direction until LED2 is ON.","Press Start key."]
  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Spin' LED is ON…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until only the 'Rinse' LED is…
  • Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'In Use', 'Soak/Wash'…
  • Drain & Spin Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' and 'Done' LEDs…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Toggle the cycle selector knob until only the 'Done' LED…
  • Fault History["From Service Mode, rotate E3 in clockwise direction until LED1 is ON.","Press Start key."]
  • Fault/Error Code Display["From the DIAGNOSTICS HOME screen, press ERROR DIAGNOSTIC button.","If there are no saved fault…
  • Manual Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Final Spin' and 'Done'…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Spin' and 'Done'…
  • Quick Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until only the 'Final Spin' LED…
  • Service Diagnostic Mode["Ensure the dryer is in standby mode (plugged in with all indicators off).","Press POWER button to…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Service Mode Entry["Ensure washer is in standby mode (plugged in with all LEDs off).","Ensure product is in OFF…
  • Service Test Mode["Activate Service Diagnostic Mode first.","From the Diagnostics Home screen, scroll down and…
  • Software Version["From Service Mode, rotate E3 in clockwise direction until LED4 is ON.","Press Start key."]
  • Software Version Display["From DIAGNOSTICS HOME, navigate to System Info > Software Version.","Version of software will be…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse', 'Final Spin'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Soak/Wash' and 'Done'…
  • UI (Rotary Switch) Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' and 'Final Spin'…
  • UI Test["From Service Mode, rotate E3 in clockwise direction until LED3 is ON.","Press Start key."]
  • UI Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Rinse' and 'Spin'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass