Model reference
Amana ADB1500ADS4
Dishwasher
12 documents61 error codes11 service modes
Available documentation
Tech Sheet
- Tech Sheet W11427956A16 pg
- Tech Sheet ADB1500ADS16 pg
- Tech Sheet W11266094A16 pg
- Whirlpool Dishwasher ADB1500aww2 Tech Sheet and Schematic2 pg
- Tech Sheet12 pg
- KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
- Fiche technique W10751168C16 pg
Service Flash
- Tall Tub Maytag Built Dishwashers Replacement Tubs Available4 pg
- TECHNICAL SERVICE POINTER - Plastic Tub Dishwashers Heating Element and Bracket Rework #R173BV4 pg
- Service Pointer - Heating Element and Bracket Rework R173BV4 pg
Bulletin
- Maytag Plastic Tall Tub Dishwashers - Door makes noises4 pg
Other
- TDD 0016 B1 pg
MyPros+ Max
Diagnose your Amana ADB1500ADS4.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (61)
CodeMeaning
1-1Control detected K1 pilot relay stuck closed.1-2Control software issue10-1Dispenser electrical problem10-3Drying fan error2-2No response from User Interface (UI)3-1Thermistor/OWI open circuit3-2Thermistor/OWI shorted3-3Failed OWI calibration4-3Wash motor not running5-1Door stuck open5-2Door stuck closed6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open7-1No heat7-2Heater stuck on8-2Drain motor electrical problem9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disc missingF1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F10E1OtherF10E3OtherF1E1ControlF1E2ControlF2-E1Control detected stuck key(s) in keypad or keypad connection.View all 61 error codes
F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failure; failed calibrationF4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F6E1Inlet WaterF6E3Inlet WaterF6E4Inlet WaterF7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F7E1HeatingF7E2HeatingF8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F8E2DrainingF8E3DrainingF9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.F9E1DiverterF9E2DiverterF9E3Diverter
Service modes (11)
- Beeper On/Off TogglePress and hold Hi Temp key for 3 seconds (tone sounds).
- Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22-20), press the HI…
- Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
- Control LockPress and hold Control Lock key for 5 seconds to turn On/Off.
- Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
- Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
- Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
- Service Diagnostic Cycle["Ensure the appliance is in Standby mode.","Press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3…
- Service Diagnostics CycleWhile in Standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1…
- Service Diagnostics with Error CodesPress any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second between key presses.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax