mypros+
Model reference

Amana OH-84DE-C/P96363-3F

Furnace

8 documents54 error codes27 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 397737216 pg
    Covers this model
  • Tech Sheet - 820490312 pg
    Covers this model
  • Tech Sheet - 820491012 pg
    Covers this model
  • Tech Sheet 8204950 WP MW Tech Sheet GH9177xlt 212 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 396846915 pg
    Covers this model
  • Instruction Sheet - 818396912 pg
    Covers this model
  • Instruction Sheet - 818472212 pg
    Covers this model

Other

  • 432243066 pg
    Covers this model
MyPros+ Max

Diagnose your Amana OH-84DE-C/P96363-3F.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (54)

CodeMeaning
:Flashing colon indicates a power failure has occurred.drnDrain pump system problemF0No error condition present.F0E2Oversuds condition detectedF0E3Overload conditionF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F10Display error.F1E1Main control fault (internal ACU failure).F1E2Motor control section of the main control has faulted.F1E3Mismatch of ACU and UIF2Membrane switch failure.F2E1UI stuck buttonF2E3UI mismatchF2E4UI software errorF2E5UI software errorF2KKey or foil pressed more than 1 minute.F2TTouch panel pressed more than 1 minute.F3E1Pressure system faultF3E2Inlet water temperature faultF3HHumidity sensor out of range.F3TTemperature sensor out of range.F4E1Heater stuck onF4E2Heater not turning onF5E1Lid switch faultF5E2Lid lock will not lock or lid lock failure.F5E3Lid lock will not unlock.F5E4Lid not opened between cyclesF6Microwave relay failure.F6E2Communication error
View all 54 error codes
F6E3Communication errorF7Power to magnetron interrupted.F7E0Loss of powerF7E1Loss of power during spinF7E2Motor drive module failureF7E3Basket engaged during washF7E4Basket re-engagement failureF7E5Shifter failure.F7E6Motor circuit openF7E7Motor unable to meet target RPM.F7E8Motor over temperatureF7E9Locked rotorF8E1Long fillF8E3Overflow or flood conditionF8E6Water hazardF9CE2PROM CheckSum error.F9EE2PROM empty.F9E1Drain pump system problemF9E2Drain pump system problemF9ME2PROM missing.F9WE2PROM write error.LFLong fillPFPower failure indication; blinks in the display after a power outage longer…Stuck KeyThe control detects that a key is stuck in the depressed position; dishwasher…

Service modes (27)

  • Automatic Function TestWith door latched, press key pads in the following sequence within 10 seconds
  • Damp Dry Test1
  • diagnosticWithin 10 seconds, press the following sequence of keys
  • Diagnostic Mode (LCD models)["Enter service mode first","Rotate timer dial through positions to access different diagnostic…
  • Factory Test1
  • Fault Code Display / Clearing["Enter Service Diagnostic Mode.","If saved fault code exists, it will be flashing in the display…
  • Idle/Service Mode (MAH5500B/MAH6500)["With washer in Off position, press and hold the Fabric Selection button and the Options…
  • Key Activation & Encoder Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • Manual Function TestWith door latched, press key pads in the following sequence within 10 seconds
  • Motor and Motor Control Test["1
  • Motor and Motor Control Test (Delay Mode Test)["Set the timer knob into the delay increments.","Press the push-to-start switch to start the…
  • Motor Phase Test["1
  • Quick Service Test (MAH5500/MAH6500 - LCD models)["1. Turn cycle selector knob to a position.","2. Press and hold the Start/Stop button.","3. The…
  • Quick Spin Test (LCD models)["Enter service mode","Set timer to appropriate position for spin test","Washer will execute spin…
  • rapid_advanceAfter a cycle has started, enter the key sequence
  • sales_demoWithin 10 seconds, press the following sequence of keys
  • Service Calibration["Enter Service Test Mode.","Select function number 052 using Soil Level/Temp buttons or cycle…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostics (Automated Test Cycle)["Enter Service Test Mode.","Select function number 051 using Soil Level/Temp buttons or cycle…
  • Service Mode (MAH5500/MAH6500 - LCD models)["Set timer to any Off position","Press and hold the Fabric Selection and Options buttons…
  • Service Test Mode (Load Control)["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • Test Mode (Self-Diagnostic)["Press the clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…
  • test_mode["Press the clock key.","Press keys 1, 2 and 3 on the keyboard.","Touch AM/PM on the touch screen…
  • Touch Panel and Electronic Control Self-Diagnostic Test Mode["Press and hold CANCEL while opening the door.","While still holding the CANCEL button, unplug the…
  • Touch Panel and Electronic Control Test (Diagnostic/Test Mode)["Press and hold CANCEL while opening the door.","While still holding the CANCEL button, unplug the…
  • Touch Panel and Microcomputer Board Self-Diagnostic Test Mode["Press the Clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass