mypros+
Model reference

Amana SL-150-UA

Furnace

6 documents43 error codes11 service modes

Available documentation

Tech Sheet

  • tech sheet w11320653 rev b28 pg
    Covers this model
  • tech sheet w11417645 revb56 pg
    Covers this model
  • Tech Sheet - W11156990 - Rev C_W1115699052 pg
    Covers this model

Installation Guide

  • Installation Instructions30 pg
    Covers this model
  • Installation Instructions32 pg
    Covers this model
  • Installation Instructions32 pg
    Covers this model
MyPros+ Max

Diagnose your Amana SL-150-UA.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
:Flashing colon indicates a power failure has occurred.E1Temperature sensing circuit is open.E2Temperature sensing circuit is shorted.E3Blower rotational speed dropped below 500 RPMs during a cycle; all outputs…E4Tumbler rotational speed dropped to 0 during a cycle; all outputs turned off.E5Dry rack sensor signal lost during a Dry Rack cycle; all outputs turned off.E6Exhaust temperature exceeded 87.7°C (190°F); all outputs turned off.F0E1Load detected in drum during Clean Washer cycle.F0E2Excessive suds detected in washer; washer is running a suds reduction routine.F0E4High temperature error during wash cycle.F0E5Off balance load detected.F12E0Communication between the Human Machine Interface and Wi-Fi Module has not been…F1E1Main relay open or shorted.F1E2MCU over- or under-voltage error.F2Touch panel failure.F3E1Pressure sensor signal missing or out of range.F3E2Wash NTC (thermistor) open or shorted.F3E5Dry NTC fault; dry temperature sensor out of range, open circuit, or short…F3E6Accelerometer error.F4E1Wash heater relay error or no feedback signal; ACU cannot detect temperature…F4E2Heating timeout.F4E4Blower error.F5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6E1No communication from the HMI detected by ACU.F6E2No communication from the ACU detected by the HMI.F6E3No communication from the MCU detected by the ACU.F7E10Motor disconnected error.F7E12MC/MCU overload.
View all 43 error codes
F7E2MC/MCU over temperature error or over current error/internal failure.F7E8MC/Motor over temperature error.F7E9Motor will not turn (locked rotor).F7EAMotor disconnected error (alternate display F7E10).F7ECMC/MCU overload (alternate display F7E12).F8E1Water inlet valve failure.F8E3Overflow condition detected.F9E1Long drain time.FCE0Communication between the Human Machine Interface and Wi-Fi Module has not been…Lo FloLong fill (alternate display of F8E1).NTC OPEN, CALL FOR SERVICEHF NTC thermistor is open.NTC SHORT, CALL FOR SERVICEHF NTC thermistor is shorted.PFPower failure occurred while the dryer was running.

Service modes (11)

  • Diagnostic Test #1 - Controls Operation["Ensure dryer is in Standby Mode (plugged in, all indicators off).","Within 5 seconds, press
  • Diagnostic Test #2 - Machine Operation["Ensure dryer is in Standby Mode (plugged in, all indicators off).","Within 3 seconds, press
  • Fault/Error Code DisplayEnter Service Diagnostic Mode; the most recent fault code is shown automatically upon entry
  • Human-Machine Interface TestFrom within Service Diagnostic Mode, press and release the 1st button used to activate Service…
  • Menu Mode (Gas/Electric Configuration)["Ensure dryer is in Standby mode (plugged in, all indicators off).","Within 3 seconds, press
  • Quick Diagnostic TestFrom within Service Diagnostic Mode, press and release the 2nd button used to activate Service…
  • Self-Diagnostic / Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Service Diagnostic Mode1. Washer must be in standby mode (plugged in, all indicators off). 2. Wait 30 seconds after…
  • Software Version DisplayFrom within Service Diagnostic Mode, press and hold the 2nd button used to activate Service…
  • Test #5a - User Interface Keypad Test["Unplug dryer or disconnect power.","Press and hold Start and Cycle End Tone buttons.","While…
  • Test #5a - User Interface Keypad Test Mode["Unplug dryer or disconnect power.","Press and hold Start and Cycle End Tone buttons.","While…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass