mypros+
Model reference

Amana CRRL-5D/P75590-6M

Microwave

4 documents39 error codes18 service modes

Available documentation

Service Manual

  • Job Aid - Microwave Ovens44 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 85337768 pg
    Covers this model
  • Instruction Sheet - 854179812 pg
    Covers this model
  • Instruction Sheet - 397921012 pg
    Covers this model
MyPros+ Max

Diagnose your Amana CRRL-5D/P75590-6M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (39)

CodeMeaning
1Dryer Thermistor Short Sensed10No Wet Clothes2Thermistor Open Sensed3Door Circuit Failure4Possible motor transistor error8Stuck Keyd1Blocked coin 1 or coin drop UI control circuit failure (coin recognition and…d2Voltage detected below 90 VAC for 8 seconds.d3Blocked coin 2 or coin drop UI control circuit failure (coin recognition and…d4Not receiving communications from installed debit card reader in Enhanced…dCDoor Circuit FailuredoDoor OpenE1Thermistor is open (open circuit detected).E2Thermistor has shorted (short circuit detected).E3User interface keyswitch or software mismatch between the control…F-01Primary control failure.F-02Stuck button or user interface mismatch (only appears in diagnostic test mode).F-22Exhaust thermistor is open.F-23Exhaust thermistor has shorted.F-26Motor drive system failure.F-28Moisture sensor strip is open (only appears in diagnostic test mode).F-29Moisture sensor strip has shorted (only appears in diagnostic test mode).F1Dryer motor control circuit error (cycles and price display disabled until…F1E1Primary control failure.F2Exhaust thermistor open, temperature drops below 18°F (>50 kΩ) for 1 minute in…F2E1Stuck button or user interface mismatchF3Exhaust thermistor shorted, temperature above 250°F (<500Ω) for 1 minute in Run…F3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E6Moisture sensor strip is open
View all 39 error codes
F3E7Moisture sensor strip has shortedF4UI is not receiving communications from CCU (cycles and price display disabled…F5CCU is not receiving communications from UI (cycles and price display disabled…F6UI Microprocessor is not able to read or verify EEPROM (cycles and price…F7UI EEPROM memory is a CRC failure (cycles and price display disabled until…FEPower source frequency errorhEHeater ErrorPFPower failure occurred while the dryer was running.tSDryer Thermistor Short Sensed

Service modes (18)

  • Console Diagnostics (within Diagnostic Test Mode)["Enter Diagnostic Test Mode as described above.","Press each button or turn the cycle selector to…
  • Customer-Focused Drying Mode Adjustment1
  • diagnostic["Enter set-up mode first.","Navigate to set-up code 6 xx or 7 xx, or have a diagnostic code…
  • Diagnostic Code DisplayEnter Service Mode, then press Wrinkle Prevent
  • Diagnostic Test Mode1
  • Diagnostic: Door Switch (within Diagnostic Test Mode)["Enter Diagnostic Test Mode.","Open the dryer door
  • Diagnostic: Moisture Sensor (within Diagnostic Test Mode)["Enter Diagnostic Test Mode.","Locate two metal strips on the face of the lint screen…
  • Dryness Adjust Mode (TEST #4a)1. Activate the diagnostic test mode and advance past saved fault codes. 2. Press and hold the…
  • Electronic Oven Control Test["1. Unplug the oven.","2. Remove the cabinet.","3. Discharge the HV capacitor with a 20,000 ohm…
  • Factory Test["Open the door","Set Temperature switch to AIR ONLY","Set Signal switch to LOUDER","Set Timer to…
  • help["Enter set-up mode.","Navigate to special pricing option 2.XX.","Press the COTTON/WHITES button to…
  • LED/Switch CheckWhile in Service Mode, press Chime and Wrinkle Prevent keys for 3 seconds to start the LED/Switch…
  • Service Diagnostic Mode1
  • Service ModeDryer must be on
  • setup["Method 1 (9150 models)
  • Software Revision DisplayWhile in Service Mode, press the Temperature key to display the software revision number.
  • System Check ModeWhile in Service Mode, press the Time and Wrinkle Prevent keys for 3 seconds. 'in' will display…
  • User Interface/Control System TestFrom within Service Diagnostic mode, press and release the 1st button used to enter Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass