mypros+
Model reference

Amana TAA600/P75751-10W

Washer

61 error codes63 service modes
MyPros+ Max

Diagnose your Amana TAA600/P75751-10W.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (61)

CodeMeaning
1Dryer Thermistor Short Sensed1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10No Wet Clothes10-1Dispenser electrical problem10-3Drying fan error2Thermistor Open Sensed2-1Control detected stuck key(s) in keypad or keypad connection.3Door Circuit Failure3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Shorted connection or component in Temperature Sensing circuit; incoming water…3-3OWI calibration failure4Possible motor transistor error4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…4-3 (cause 2)Control Motor Drive circuit or Sense circuit failure preventing wash motor…5-1Door stuck open5-2Door stuck closed6-1Low or no water6-2Fill valve electrical problem6-3Suds or air in pump detected.6-4Float switch open6-6Incoming water under 84°F (29°C)6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8Stuck Key8-1Slow drain8-2Drain motor electrical problem8-3Drain motor stuck on
View all 61 error codes
9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk missingdCDoor Circuit FailuredoDoor OpenE0No errors present in the ice maker system.E1Manufacturing codeE2Ice maker errorE3Manufacturing codeE4Manufacturing codeE5Ice maker errorE6Manufacturing codeErManufacturing codeF0-E0Default F codeF1-E0/E1/E2Electronic control malfunction.F1-E3/E4/E5Electronic control malfunction.F2-E0Keypad keytail not connected.F2-E1Keypad keytail not connected.F2-E3Key held down too long, or key is shorted.F3-E0Temperature sensor opened (lower cavity).F3-E1Temperature sensor shorted (lower cavity).F3-E2Temperature sensor opened (microwave).F3-E3Temperature sensor shorted (microwave).F4-E0Function not used.F5-E0Function not used.F6-E0Function not used.F6-E1Microwave cavity over temperature during cooking.F8-E0/E1/E2/E3/E4Function not used.FEPower source frequency errorhEHeater ErrortSDryer Thermistor Short Sensed

Service modes (63)

  • Clear Diagnostic Codes1
  • Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
  • Diagnostic Code DisplayEnter Service Mode, then press Wrinkle Prevent
  • Display Software Revision Number1
  • Fault code displayPress and hold UPPER OFF key for 5 seconds
  • LED/Switch CheckWhile in Service Mode, press Chime and Wrinkle Prevent keys for 3 seconds to start the LED/Switch…
  • Service Diagnostics Cycle1
  • Service Diagnostics Mode["Press SW1 and SW2 simultaneously for 3 seconds.","Release both buttons when you hear the CHIME…
  • Service ModeDryer must be on
  • Service Test - 38 Forced Defrost ModeWhile in Service Diagnostics Mode, navigate to step 38. Select SW3 to set mode
  • Service Test 1 - FC Thermistor["Enter Service Diagnostics Mode.","Navigate to step 1 (display shows 01).","The board will…
  • Service Test 11 - Dispenser Lighting["Enter Service Diagnostics Mode.","Navigate to step 11.","Pressing SW3 will change the dispenser…
  • Service Test 15 - Ice Level Sensor["Enter Service Diagnostics Mode.","Navigate to step 15.","Displays the Ice Bin Status in real time…
  • Service Test 16 - RC Left Door Switch Input["Enter Service Diagnostics Mode.","Navigate to step 16.","Displays the RC Door status in real time…
  • Service Test 17 - RC Right, Pantries, FC Doors Switch Input["Enter Service Diagnostics Mode.","Navigate to step 17.","Displays the FC Door status in real time…
  • Service Test 18 - Ice Door Motor["Enter Service Diagnostics Mode.","Navigate to step 18.","Press ice paddle and verify that the…
  • Service Test 19 - Ice Maker Fill Tube Heater Status["Enter Service Diagnostics Mode.","Navigate to step 19.","Control the Ice Maker Fill Tube Heater…
  • Service Test 2 - RC Thermistor["Enter Service Diagnostics Mode.","Navigate to step 2.","The board will automatically check the…
  • Service Test 20 - Water Filter Usage Rating["Enter Service Diagnostics Mode.","Navigate to step 20.","Displays in two sequential flashes the…
  • Service Test 21 - Water Filter Time Rating["Enter Service Diagnostics Mode.","Navigate to step 21.","Displays in two sequential flashes the…
  • Service Test 22 - Water Filter Usage["Enter Service Diagnostics Mode.","Navigate to step 22.","Displays in two sequential flashes the…
  • Service Test 23 - Water Filter Time["Enter Service Diagnostics Mode.","Navigate to step 23.","Displays in two sequential flashes the…
  • Service Test 24 - Water Filter Reset["Enter Service Diagnostics Mode.","Navigate to step 24.","Displays in two sequential flashes the…
  • Service Test 26 - Main Control Software Version["Enter Service Diagnostics Mode.","Navigate to step 26.","Displays in three sequential flashes the…
  • Service Test 27 - Dispenser UI Control Software Version["Enter Service Diagnostics Mode.","Navigate to step 27.","Displays in three sequential flashes the…
  • Service Test 29 - Low Voltage IDI Software Version["Enter Service Diagnostics Mode.","Navigate to step 29.","Displays in three sequential flashes the…
  • Service Test 3 - Evaporator Fan Motor and Air Baffle Motor["Enter Service Diagnostics Mode.","Navigate to step 3.","Depress SW3 to cycle
  • Service Test 31 - Touch Input Module Software["Enter Service Diagnostics Mode.","Navigate to step 31.","Displays in three sequential flashes the…
  • Service Test 32 - Ambient Thermistor UI Control["Enter Service Diagnostics Mode.","Navigate to step 32.","Internal board test
  • Service Test 33 - Humidity Sensor UI Control["Enter Service Diagnostics Mode.","Navigate to step 33.","Relative Humidity Test
  • Service Test 34 - Vertical Mullion Heater Mode["Enter Service Diagnostics Mode.","Navigate to step 34.","Set the Vertical Mullion Heater Sensor…
  • Service Test 35 - Vertical Mullion Heater Status["Enter Service Diagnostics Mode.","Navigate to step 35.","Control the Vertical Mullion Heater…
  • Service Test 36 - Ice Box Fan["Enter Service Diagnostics Mode.","Navigate to step 36.","Control Ice Box Fan using SW3
  • Service Test 37 - Ice Box Thermistor["Enter Service Diagnostics Mode.","Navigate to step 37.","The board will check the resistance…
  • Service Test 38 - Forced Defrost Mode["Enter Service Diagnostics Mode.","Navigate to step 38.","Set the Forced Defrost Mode by selecting…
  • Service Test 39 - RC Evap Thermistor["Enter Service Diagnostics Mode.","Navigate to step 39.","The board will check the resistance…
  • Service Test 4 - Compressor/Condenser Fan Motor/Evaporator Fan["Enter Service Diagnostics Mode.","Navigate to step 4.","There will be a delay of 3 seconds before…
  • Service Test 40 - Horizontal Mullion Heater Mode["Enter Service Diagnostics Mode.","Navigate to step 40.","Set the Horizontal Mullion Heater Sensor…
  • Service Test 41 - Horizontal Mullion Heater Status["Enter Service Diagnostics Mode.","Navigate to step 41.","Control the Horizontal Mullion Heater…
  • Service Test 42 - UI EEPROM Control Software Version["Enter Service Diagnostics Mode.","Navigate to step 42.","Displays in three sequential flashes the…
  • Service Test 45 - Ice Maker Water Fill Test["Enter Service Diagnostics Mode.","BEFORE INITIATING THIS TEST, GO TO STEP 57, INITIATE ICE MAKER…
  • Service Test 46 - Water Dispensing Test["Enter Service Diagnostics Mode.","Navigate to step 46.","Press the water pad to initiate a water…
  • Service Test 5 - Compressor Status/Speed["Enter Service Diagnostics Mode.","Navigate to step 5.","Initial Display
  • Service Test 56 - Ice Maker Error Codes["Enter Service Diagnostics Mode.","Navigate to step 56.","Displays active Ice Maker Error Codes on…
  • Service Test 57 - Ice Maker Harvest["Enter Service Diagnostics Mode.","Navigate to step 57.","Press SW3 to activate a Harvest sequence
  • Service Test 58 - Ice Maker Heater Activation and Thermistor["Enter Service Diagnostics Mode.","Navigate to step 58.","Press SW3 to activate the Ice Maker…
  • Service Test 59 - Ice Maker Motor["Enter Service Diagnostics Mode.","Navigate to step 59.","Press SW3 to activate a Motor sequence…
  • Service Test 60 - Pantry UI Software Version["Enter Service Diagnostics Mode.","Navigate to step 60.","Displays in three sequential flashes the…
  • Service Test 63 - All Pantry UI Indicators["Enter Service Diagnostics Mode.","Navigate to step 63.","All pantry LED indicators and pantry UI…
  • Service Test 64 - Pantry UI Button Test["Enter Service Diagnostics Mode.","Navigate to step 64.","Displays the pantry UI Buttons status."]
  • Service Test 65 - Pantry Thermistor["Enter Service Diagnostics Mode.","Navigate to step 65.","The board will check the resistance…
  • Service Test 66 - Manufacturing Codes["Enter Service Diagnostics Mode.","Navigate to step 66.","Displays the active manufacturing error…
  • Service Test 67 - Water Filter Switch Status["Enter Service Diagnostics Mode.","Navigate to step 67.","Displays the water filter switch status…
  • Service Test 73 - Pantry Heater Status["Enter Service Diagnostics Mode.","Navigate to step 73.","Control the Pantry Heater selecting SW3…
  • Service Test 76 - Icebox Fascia Heater["Enter Service Diagnostics Mode.","Navigate to step 76.","Control the Icebox Fascia Heater…
  • Service Test 77 - Defrost Thermistor["Enter Service Diagnostics Mode.","Navigate to step 77.","The board will check the resistance…
  • Service Test 78 - Pantry UI Flashmap Version["Enter Service Diagnostics Mode.","Navigate to step 78.","Displays in three sequential flashes the…
  • Service Test 8 - All UI Indicators["Enter Service Diagnostics Mode.","Navigate to step 8.","All LED indicators and UI display digits…
  • Service Test 80 - LED Driver Software Version["Enter Service Diagnostics Mode.","Navigate to step 80.","Displays in three sequential flashes the…
  • Service Test 81 - LED Driver Flash Software Version["Enter Service Diagnostics Mode.","Navigate to step 81.","Displays in three sequential flashes the…
  • Service Test 9 - UI Button and Pad Test["Enter Service Diagnostics Mode.","Navigate to step 9.","Displays the user Interface Buttons and…
  • Software Revision DisplayWhile in Service Mode, press the Temperature key to display the software revision number.
  • System Check ModeWhile in Service Mode, press the Time and Wrinkle Prevent keys for 3 seconds. 'in' will display…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass