mypros+
Model reference

Caloric DCR-211-1H-OM

Dishwasher

3 documents95 error codes28 service modes

Available documentation

Tech Sheet

  • Basic Operation of Commercial Stacked Washer/dryer20 pg
    Covers this model
  • Tech Sheet W1061005912 pg
    Covers this model
  • Whirlpool Dishwasher WDF760SADM0 Tech Sheet W1061005912 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR-211-1H-OM.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (95)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory or control board, incompatible software components…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection or…3-3OWI (optical soil sensor) calibration failure.4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…5-1Door stuck open5-2Door stuck closed6-1Inlet water low/no water (mechanical problem)6-2Inlet water fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Incoming water cool6-8Regen valve electrical problem7-1No heat7-1 (flowmeter)Disconnected or damaged flowmeter.7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain motor stuck on8-5Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk missingC1Blocked coin 1 or coin drop control circuit failure (coin recognition and price…C2Blocked coin 2 or coin drop control circuit failure (coin recognition and price…
View all 95 error codes
d 13Coin 2 errord 16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorEdNot receiving communications from installed debit card reader in Enhanced…F 01Dryer motor control circuit errorF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 23Dryer exhaust thermistor shorted errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnectedF 34Load detected in washer during Washer Cleanout Cycle.F 70Communication failure between CCU and UIC.F 71Dryer communication failure from UIC to dryer CCUF 73UIC failure (washer) / UIC Microprocessor error (dryer)F 74UIC EEPROM errorF01MCC errorF11Motor Control Module (MCM) failure, possibly due to repeated under-voltage or…F1E1Indicates a CCU (Cycle Control Unit) problem.F20No water detected entering the washerF21Excessive drain timeF22Door lock errorF24Water temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between the Central Control Unit (MCC) and the Motor…F29Door unlock failureF2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F31Motor overheating or related MCM fault condition.F33Pump disconnectedF34Load detected in washer during the washer cleaning cycle.F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4E1No voltage detected at the heater relay; only appears in Diagnostic Test Mode.F4E3Restricted/low air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F6E1Communication error from UI to CCU; communication between CCU and UI has not…F6E2Communication error from CCU to UI; communication between CCU and UI has not…F70Communication failure between the Central Control Unit (MCC) and the User…F73User Interface (UI) failureF74User Interface (UI) failureL2Low L2 voltage (less than 50V) detected at the CCU.LdWasher lid sense error on control board or due to power line interference…LFWater level detection error on control board or due to power line interference…LSMotor sense error detected on control board or due to power line interference.LVVoltage detected below 90 VAC for 8 seconds.PFPower failure occurred while the dryer was running.SdLast drain occurring during final spin was slow.SFLast fill was slow.tFWater temperature sense error when equipped with temperature sensing water…

Service modes (28)

  • Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
  • Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
  • Customer-Focused Dryness Level Adjustment1
  • diagnostic mode["Enter set-up mode first.","While in any of the set-up codes 1 through 6, anytime a diagnostic…
  • Diagnostic Mode (Washer Diagnostic Mode)["First access the Setup Mode (Start Operating Set-up).","Press and hold the QUICK CYCLE button for…
  • Dryer Field Diagnostic Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS) button."]
  • field diagnostic cycle["Enter diagnostic mode (entire display flashing).","Press the LOWER MIDDLE key pad to start the…
  • help mode["Enter set-up mode first.","Navigate to special pricing option mode (code 2.XX).","Press the LOWER…
  • Help Mode (Aide Mode)["PD models
  • Install Diagnostics1
  • Loads Test Mode1. Dryer must be in standby mode (plugged in with all indicators off). 2. Within 5 seconds: press…
  • Manual Overview Test["Enter Diagnostic Mode (display is flashing).","Press the WHITES button."]
  • Quick Overview Test["Enter Diagnostic Mode (display is flashing).","Press the DELICATES AND KNITS button."]
  • Quick Spin Program (Drain and Spin)["Enter Diagnostic Mode (display is flashing).","Press the COLORS button."]
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Service Access Code (Code d'accès pour entretien)["Works only on washers configured for $0.00 sale price without Special Price, and Coin/Debit…
  • Service Diagnostic Mode1. Dryer must be in standby mode (plugged in with all indicators off). 2. Select any three buttons…
  • Service Diagnostics Cycle1
  • set-up mode["PD Models
  • Set-Up Mode (Coin Payment)["Insert service switch key and turn counter-clockwise."]
  • Setup Mode (Parameter Setting Mode)["PD models
  • Software Version Display1
  • Washer Cleaning Program["Enter Diagnostic Mode (display is flashing).","Press the BRIGHTS button."]
  • Washer Cleanout Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cycle Credit (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Manual Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Quick Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Spin Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax