mypros+
Model reference

Fisher & Paykel DS605

Dishwasher

17 documents14 error codes22 service modes

Available documentation

Service Manual

  • Diagnostic Manual DishDrawer39 pg
    Covers this model
  • DishDrawer 605 Service Summary and Fault Code Descriptions8 pg
    Covers this model
  • F9 Diagnostic Manual DishDrawer™ Ph5 & 621 pg
    Covers this model
  • Service Manual DishDrawer™ Dishwasher55 pg
    Covers this model

Bulletin

  • Service Bulletin - DISHDRAWER F9 Fault Code5 pg
    Covers this model
  • Service Bulletin - DishDrawer Wash Program Selector Button & Refrigeration Ordering Spare Parts7 pg
    Covers this model
  • DishDrawer New 5.1 Software Controller2 pg
    Covers this model
  • Fisher & Paykel Appliances Service Bulletins October 20088 pg
    Covers this model
  • DISHDRAWER Service and General Bulletins8 pg
    Covers this model
  • General Bulletin - DishDrawer Motor Rotor Colour Change / Blocked Water Softener5 pg
    Covers this model
  • Fisher & Paykel Appliances General Bulletins November 20085 pg
    Covers this model
  • Tech Bulletin Bundle2 pg
    Covers this model
  • Gas Cooktop New Gas Innovalves – Service Version Change / Dishdrawer Pop Top Diaphragm Lid11 pg
    Covers this model

Service Flash

  • FisherPaykelBulletins6200811 pg
    Covers this model

Installation Guide

  • User guide DishDrawer DS605 and DD605 models112 pg
    Covers this model

Other

  • Diagnostics DD605 Dishwasher39 pg
    Covers this model
  • S FDWD 08 02 F9 Fault Code3 pg
    Covers this model
MyPros+ Max

Diagnose your Fisher & Paykel DS605.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (14)

CodeMeaning
F1The bottom controller flood detector has activated.F2Motor Not Starting.F3Water Temperature greater than 185 degrees F (85 degrees C).F4Element on for more than 3 hours and water has not reached required temperature.F5Lid Actuator Jammed Up or Down.F6Lid Motors run but do not reach Stall current.F7No Lid Motor Current Detected.F8Ground (Earth) Leakage Fault.F9Electronics / Power Supply Failure.FFTop tub not responding.U1Fill valve open for 3 minutes and wash pump has not primed (No Tap symbol on…U2Restricted lid travelU3Filled too quickly or failed to drain (not displayed to customer, recorded in…U4Advisory fault

Service modes (22)

  • Continuous Cycle Test Mode1. Ensure DishDrawer is in Power Off mode. 2. Press and hold KEYLOCK, then press START/PAUSE for 5…
  • Continuous Cycle Test Mode – Level Four["From Level Three, press POWER to advance to Level Four.","Press START/PAUSE to enter."]
  • Continuous Cycle Test Mode (Level 4)From diagnostics entry, press POWER three times (LCD shows 'CC')
  • Diagnostics Entry["Ensure the DishDrawer is in Power Off mode (no display on LCD / badge LEDs off).","If product was…
  • Diagnostics Mode - Continuous Cycle Sub Mode["Enter from Fast Test Cycle sub mode by pressing the Power button once.","CC will be displayed on…
  • Diagnostics Mode - Display/Download Diagnostic Sub Mode["Ensure appliance is in Power Off mode.","Press and hold Keylock and Start/Pause buttons for about…
  • Diagnostics Mode - Fast Test Cycle Sub Mode["Enter from Hardware Output Test sub mode by pressing the Power button once.","FC will be…
  • Diagnostics Mode - Hardware Output Test Sub Mode["Enter from Display/Download Diagnostic sub mode by pressing the Power Button once.","LCD will…
  • Display Mode – Level One["Enter diagnostics mode (KEYLOCK + START/PAUSE for 5 seconds).","Level One is displayed first…
  • Display/Download Mode (Level 1)Enter diagnostics mode. First level shown automatically
  • Fast Test Cycle1. Ensure DishDrawer is in Power Off mode. 2. Press and hold KEYLOCK, then press START/PAUSE for 5…
  • Fast Test Cycle – Level Three["From Level Two, press POWER to advance to Level Three.","Press START/PAUSE to enter Fast Test…
  • Fast Test Cycle (Level 3)From diagnostics entry, press POWER twice (LCD shows 'FC')
  • Fault Display/Download Mode1. Ensure DishDrawer is in Power Off mode (no display on LCD). 2. Press and hold KEYLOCK, then…
  • Hardware Output Diagnostic Test Mode1. Ensure DishDrawer is in Power Off mode. 2. Press and hold KEYLOCK, then press START/PAUSE for 5…
  • Hardware Output Diagnostic Test Mode (Level 2)From diagnostics entry, press POWER once to reach this level (LCD shows 'HO')
  • Hardware Output Test Mode – Level Two (HO mode)["From Level One, press POWER to advance to Level Two (LCD displays 'HO').","Press START/PAUSE to…
  • Option Adjustment Mode1
  • Show Off / Showroom Wash Mode1
  • Show Off/Showroom Wash ModeWith the DishDrawer powered up and turned on, press and hold ECO and POWER simultaneously for 5…
  • Temperature & Voltage Display Mode1
  • Temperature and Voltage Display Mode["Start a wash cycle (must be in Wash mode with cycle active).","Press and hold Keylock for 5…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax