Model reference
GE ZET938
Oven
15 documents10 error codes22 service modes
Available documentation
Service Manual
- 30" Electric Convection Wall Oven with Erc Control and Motorized Door Lock Service Manual2 pg
- Owner's Manual - 27″ and 30″ Convection Wall Oven48 pg
- ServiceManual 31 914435 pg
- 31 9098 GE Monogram 27 and 30 inch Wall Ovens Service Manual51 pg
- GE and Monogram 27-In. and 30-In. Wall Ovens Technical Service Guide51 pg
- GE and Monogram 27-In. and 30-In. Wall Ovens Technical Service Guide51 pg
- Owner's Manual 27″ and 30″ Convection Wall Oven48 pg
Tech Sheet
- The Monogram Black Book103 pg
- Appliance Diagnostic Modes Range GE Consumer & Industrial Technical Training255 pg
Bulletin
- Service Bulletin RANGE RA 04-041 pg
- Calibration Error and F0 Display1 pg
- Service Bulletin - Calibration Error and F0 Display1 pg
Training
- GE and Monogram 27-In. and 30-In. Wall Ovens Technical Service Guide51 pg
Installation Guide
- Installation Instructions - 30" Built-In Wall Oven16 pg
- Built-In Wall Oven Installation Instructions40 pg
MyPros+ Max
Diagnose your GE ZET938.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (10)
CodeMeaning
FFunction error code indicated by 'F' followed by a number or letter flashing in…F0Shorted OFF key on the key panel.F2Oven over-temperature conditionF3Open oven sensor circuit (resistance over 2900-3000 ohms depending on model).F4Shorted oven sensor circuit (resistance under 950 ohms).F5Sensor circuit supervisor failure.F7Shorted key matrix or START key.F8EEPROM data shift failure.F9Cooling fan stalls while oven above 650°F, or other cause of open thermal…FFLoss of latch motor (door lock) safety circuit.Service modes (22)
- Advantium 120 Demo Mode1
- Control Lockout["Press the 9 and 0 pads at the same time for 3 seconds until the display shows 'LOC ON'."]
- Electronic Control Showroom Demonstration Mode (Refrigerators)Press and hold the FZ-Colder and FF-Warmer control pads simultaneously until beeps sound.
- Glass Touch Parameter Reset (Control Panel Opened or Not Operating)1) Press Bake and Broil keys simultaneously
- Glass Touch Parameter Setting (Control Not Replaced)1
- Glass Touch Parameter Setting (New Part Installation)1) Reassemble control panel and return oven to normal installation
- J2S968/JGS968/JGSP48 Fault Code Recall["Press TIMER, CLOCK, and MIN DOWN (or 9) key to get Fault Codes to appear."]
- JB905/968/988 Fault Code Recall["Press TIMER and CLOCK (or 9) key to get Fault Codes to appear."]
- JP938/JP968 Cooktop Calibration Mode["Clear everything from the top of the glass.","Lock the control by pressing the LOCK key for 3…
- JP938/JP968 Cooktop Technician Mode["Lock cooktop by holding CONTROL LOCK key for 3 seconds.","Control will beep 2 times and LOCK…
- LOC REF Procedure (JCK915/JCT915/JK915/JT915/JK955/JT955/ZEK938/ZET958)["Reinitiate LOC REF procedure by pressing BAKE/BROIL simultaneously.","For digital keypads press 9…
- Oven Calibration1. Press and hold Bake & Broil pads until SF appears in display. 2. Press Bake pad to enter oven…
- Oven Calibration ModePress and hold BAKE & BROIL pads until SF appears in display
- Oven Thermostat Adjustment["Press the BAKE and BROIL HIGH/LOW pads at the same time for 3 seconds until the display shows…
- Recall Stored F-codesPress TIMER, CLOCK, and MIN DOWN (or 9) together to recall stored fault codes from EEPROM.
- Recall Stored Fault CodesPress TIMER, CLOCK, and MIN DOWN (or 9) together.
- Sabbath Mode (Ovens)Activated via oven controls per model instructions
- Sabbath Mode (Refrigerators)Install Kit ZSAB1 behind the refrigerator's top grille panel
- Sales ModePress CLOCK and TIMER pads at the same time.
- Special Features (SF) Mode["Press the BAKE and BROIL HIGH/LOW pads at the same time for 3 seconds until the display shows…
- Special Functions (SF) ModePress and hold BAKE and BROIL pads simultaneously for 2 seconds
- Trivection Service Mode["Disconnect main power to the oven for at least 15 seconds.","Reconnect power and enter 0803 on…
Full entry steps, exit procedures, and test sequences are available in Max.
Related GE oven models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax