Model reference

Jenn-Air JDB9600CWX0

Name: Jenn-Air JDB9600CWX0
Brand: Jenn-Air

Dishwasher

4 documents31 error codes5 service modes

Available documentation

Service Manual

Flush-Mount Dishwasher Service Manual193 pg
Covers this model

Service Flash

Technical Service Pointer - Power Cord Rework6 pg
Covers this model

Tech Tip

custompanelinstructions-jdb9600cwx-ii.pdf1 pg
Covers this model

Installation Guide

Installation Instructions32 pg
Covers this model

MyPros+ Max

Diagnose your Jenn-Air JDB9600CWX0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Jenn-Air Dishwasher

CL on my Jenn-Air JDB9600CWX0

M+

Child lock / button lock is active;

From Tech Sheet W14960735, p.27:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part W10810403

Door lock assembly

Error codes (31)

CodeMeaning

CLChild lock / button lock is active; displayed when any button is pressed while…E:00No error present in the system.E:01Pump control or pump switchover defective.E:02Working relay for heater defective; appliance operates without heater.E:03Working relay for auxiliary heater defective; appliance operates without…E:04Ground fault at zeolite heater or safety relay heater defective; appliance…E:05Internal fault on power module; triac for water switch motor defective, water…E:06Door Hall sensor fault; wire to Hall sensor interrupted or Hall sensor…E:07Fan defective or blocked, or fan module defective; appliance operates without…E:08Heat pump detects too low water level in pump sump.E:09Heating circuit interrupted (resistance, supply wires, contacts of the safety…E:10Zeolite drying system fault E:11NTC resistance values outside permitted range or wire/plug interrupted…E:12NTC resistance values outside permitted range; appliance operates without…E:13Heating fault E:14No impulses from flow sensor although water is detected by heat pump; programme…E:15Base carrier safety switch active indicating water in the base pan; appliance…E:16Water supply (impulses from flow sensor) detected without activation of the…E:17Water supply rate too high according to flow sensor; programme stops with…E:18Filling fault E:20Resistance values of heat pump (circulation pump) wrong; programme ends.E:21Circulation pump fault E:22Residual water in the pump sump due to dirty filters; programme ends.E:23Resistance values of drain pump wrong; programme ends.E:24Drain pump fault E:25Drain pump fault E:26Water switch fault E:27Undervoltage fault E:28AquaSensor fault E:29Undervoltage (<170V / 190V) causing appliance to stop in current position…

View all 31 error codes

E:30Overvoltage (>290V); appliance switches off.

Service modes (5)

Customer Service Test Programme (P:2)["Enter Service Program (P:0 displayed).","Press button B until P:2 is displayed.","Press button C…
Demonstration Programme (P:7)["Enter Service Program (P:0 displayed).","Press button B until P:7 is displayed.","Press button C…
Demonstration Programme (P:8)["Enter Service Program (P:0 displayed).","Press button B until P:8 is displayed.","Press button C…
Error Memory Readout (P:1)["Enter Service Program (P:0 displayed).","Press button B until P:1 is displayed.","Press button C…
Service Program Entry["Switch on the appliance.","If appliance is in a rinsing program, carry out Reset (press Start…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass