mypros+
Model reference

Jenn-Air JDTSS244GS0

Dishwasher

5 documents86 error codes9 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11427964 - Rev A2 pg
    Covers this model
  • W11427958 - Rev A15 pg
    Covers this model
  • Tech Sheet12 pg
    Covers this model
  • KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air JDTSS244GS0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (86)

CodeMeaning
1-1Control detected K400 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error12-1No communication between ECM and control12-2No link between ECM and wireless router12-3No link between ECM and Internet12-5Antenna B problem12-7Provisioning problem2-1Control detected stuck key(s) in keypad or keypad connection.2-2UI cannot communicate with main control; loose UI connection or wrong control…3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Shorted connection or component in Temperature Sensing circuit; incoming water…3-3OWI calibration failure, or drain hose check valve not sealing.4-4Wash motor failure5-1Door stuck open5-2Door stuck closed6-1Low/No water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-7Disconnected or damaged flowmeter.6-8Water softener regeneration valve electrical problem7-1No heat7-2Heater stuck on8-4Drain motor electrical problem9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disc missing
View all 86 error codes
9-4Lower spray arm errorF1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F10E1OtherF10E2OtherF10E3OtherF12E1Smart GridF12E2Smart GridF12E3Smart GridF12E5Smart GridF12E7Smart GridF1E2ControlF2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F2E2User InterfaceF3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failure; failed calibrationF3E1Thermistor/OWIF3E2Thermistor/OWIF3E3Thermistor/OWIF4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F4E4Wash motorF5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F5E1Door switchF5E2Door switchF6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F6E1Inlet waterF6E2Inlet waterF6E3Inlet waterF6E4Inlet waterF6E7Inlet waterF6E8Inlet waterF7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F7E1HeatingF7E2HeatingF8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F8E4DrainingF9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.F9E1DiverterF9E2DiverterF9E3DiverterF9E4Diverter

Service modes (9)

  • Beeper On/Off TogglePress and hold Hi Temp key for 3 seconds (tone sounds).
  • Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22-20), press the HI…
  • Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
  • Control LockPress and hold Control Lock key for 5 seconds to turn On/Off.
  • Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
  • Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
  • Service Diagnostics Cycle["With dishwasher in Standby, press START/RESUME to wake up control panel.","Press any three keys…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass