Model reference
Jenn-Air JJW9330DDB
Oven
6 documents36 error codes27 service modes
Available documentation
Tech Sheet
- Tech Sheet - 1602654510 pg
Service Manual
- Service Manual - Electric Wall Ovens37 pg
- Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
- FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
Installation Guide
- Instruction Sheet2 pg
- Installation Instructions16 pg
MyPros+ Max
Diagnose your Jenn-Air JJW9330DDB.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (36)
CodeMeaning
1c1cShorted key detected on the control circuit board.1c2cKeyboard tail disconnected from control board.1c31Cancel key circuit problem (upper/single oven cavity).1c32Cancel key circuit problem (lower oven cavity).1c4cPower micro communication failure (UH control only).1c6cEEPROM error1c7cControl not calibrated1c81Cook profile corrupted in EEPROM (upper/single oven cavity, UH control only).1c82Cook profile corrupted in EEPROM (lower oven cavity, UH control only).1c8cCooking program error1d11Runaway temperature (650°F) with door unlocked, upper/single oven cavity.1d12Runaway temperature (650°F) with door unlocked, lower oven cavity.1d21Runaway temperature (950°F) with door locked, upper/single oven cavity.1d22Runaway temperature (950°F) with door locked, lower oven cavity.3d11Temperature sensor open (infinite resistance), upper/single oven cavity.3d12Temperature sensor open (infinite resistance), lower oven cavity.3d21Temperature sensor shorted (0 ohms resistance), upper/single oven cavity.3d22Temperature sensor shorted (0 ohms resistance), lower oven cavity.3d41Meat probe shorted (probe resistance less than 0 ohms, UH control only).3d51Meat probe not calibrated4d11Door switch position failure during clean or keyboard lockout, upper/single…4d12Door switch position failure during clean or keyboard lockout, lower oven cavity4d21No reverse airflow fan rotation (no or low RPM), upper/single oven cavity.4d22No reverse airflow fan rotation (no or low RPM), lower oven cavity (UH control…4d31Reverse airflow fan state error4d32Reverse airflow fan state error4d41High reverse airflow fan rotation (high RPM), upper/single oven cavity (UH…4d42High reverse airflow fan rotation (high RPM), lower oven cavity (UH control…4d51Door switch circuit failure4d52Door switch circuit failureService modes (27)
- 24 Hour Clock TogglePress and hold Cancel and Favorite pads for 3 to 5 seconds.
- Child LockoutPress and hold Cancel and Cook & Hold pads for 3 seconds
- Clock Display TogglePress and hold Cancel and Clock pads for 3 to 5 seconds.
- Diagnostic Code DisplayPress and hold AUTOSET (0) pad for 3 to 5 seconds at power-up to enter Diagnostic Code Display mode.
- Diagnostic Code Display (H1/H2 via Quick Test)Enter Quick Test mode, then press COOK & HOLD to display last diagnostic code, or press AUTOSET to…
- Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
- Diagnostic Code Display Mode (H1/H2 Control)Press and hold the AUTOSET pad for 3 seconds at power-up
- Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
- Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
- Factory Default ResetPress and hold Cancel and Keep Warm pads for 3 to 5 seconds.
- Faults Access (EOC III Controls)1
- One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
- Oven Temperature Adjustment1
- Quick TestPress and hold CANCEL and BROIL pads simultaneously for 3 to 5 seconds
- Quick Test Mode (EOC III Controls)1
- Quick Test Mode (H1 Controls - Convection Model)1
- Quick Test Mode (H1 Controls - Non-Convection Model)1
- Quick Test Mode (H1/H2 Control)1
- Quick Test Mode (H2/H2.5 Controls)1
- Quick Test Mode (H3 Controls)1
- Quick Test Mode (M1/M2 Controls)1
- Quick Test Mode (NSC Non-Self Clean Controls)1
- Sabbath ModeHold CLOCK pad for 3 to 5 seconds to activate Sabbath mode.
- Service Mode (EOC III Controls)1
- Temperature Display Toggle (F/C)Press and hold Cancel and Bake pads for 3 to 5 seconds.
- Test Mode (UH Controls)1
- Test Mode (UH1/UH2 Control)1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Jenn-Air oven models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass