Model reference

Jenn-Air JDS8850BDW

Name: Jenn-Air JDS8850BDW
Brand: Jenn-Air

Range

8 documents36 error codes38 service modes

Available documentation

Tech Sheet

Technical Information Dual Fuel Slide-In Range16 pg
Covers this model

Service Manual

maytag-jenn-air73 pg
Covers this model
Maytag Jenn Air Dual Fuel Slide In Range Service Manual73 pg
Covers this model
Service Manual - Dual Fuel Slide-In Range73 pg
Covers this model
Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
Covers this model
Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
Covers this model
Failure Codes And Wiring Diagrams For Maytag Heritage Gas & Electric Ranges124 pg
Covers this model

Installation Guide

Installation Instructions13 pg
Covers this model

MyPros+ Max

Diagnose your Jenn-Air JDS8850BDW.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Jenn-Air Range

1c1c on my Jenn-Air JDS8850BDW

M+

Shorted key detected on the membrane

From Tech Sheet W17556668, p.40:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (36)

CodeMeaning

1c1cShorted key detected on the membrane keyboard.1c2cMembrane keyboard disconnected.1c31Cancel key circuit problem (cancel key improper value) on upper/single oven…1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cBoard-to-board communication failure.1c6cEEPROM hardware fault.1c7cControl not calibrated.1c81EEPROM CRC error 1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cEEPROM CRC error 1d11Unlocked runaway temperature 1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Locked runaway temperature 1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Temperature sensor open circuit.3d12Temperature sensor failure (open) on lower oven cavity 3d21Temperature sensor shorted.3d22Temperature sensor failure (short) on lower oven cavity 3d41Meat probe shorted.3d51Meat probe not calibrated.4d11Door switch not closed when locked.4d12Door switch position failure 4d21No cooling fan rotation detected.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Cooling fan on when de-energized.4d32Reverse Airflow Fan state error 4d41Cooling fan overspeed.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit fault.4d52Door switch circuit failure

View all 36 error codes

9d11Door latch will not lock.9d12Door latch will not lock on lower oven cavity 9d21Door latch will not unlock.9d22Door latch will not unlock on lower oven cavity 9d31Door latch both locked and unlocked simultaneously.9d32Door latch both locked and unlocked simultaneously on lower oven

Service modes (38)

Control LockoutPress the Back and Setup pads simultaneously for 5 seconds to lock.
Control Reset1
Demo Mode1
Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
Display Test1
Faults Access1
Faults Access (EOC III Controls)1
Faults Access (EOC III)1
One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
One-Watt Standby Mode (NSC)Press and hold Cancel and Less
Quick Test1
Quick Test Mode (EOC III Controls)1
Quick Test Mode (EOC III)1
Quick Test Mode (H1 Controls - Convection Model)1
Quick Test Mode (H1 Controls - Non-Convection Model)1
Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H2/H2.5 Controls)1
Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H3 Controls)1
Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (M1/M2 Controls)1
Quick Test Mode (NSC Non-Self Clean Controls)1
Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
Service Mode1
Service Mode (EOC III Controls)1
Service Mode (EOC III)1
Software Versions Access1
Test Mode (UH Control)1
Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass