Model reference

KitchenAid KDFE104D

Name: KitchenAid KDFE104D
Brand: KitchenAid

Dishwasher

5 documents26 error codes3 service modes

Available documentation

Tech Sheet

KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
Covers this model

Service Flash

Door Not Sealing Properly/Leak Potential3 pg
Covers this model
Technical Service Pointer - Dishwashers with Mini-Dispenser3 pg
Covers this model
Technical Service Pointer #W11296667 - Tall Tub Dishwashers Upper-Rack Rails Separating3 pg
Covers this model
Technical Service Pointer - W10841713 (Door Clicking)6 pg
Covers this model

MyPros+ Max

Diagnose your KitchenAid KDFE104D.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·KitchenAid Dishwasher

F1-E1 on my KitchenAid KDFE104D

M+

Control detected K2 pilot relay stuck

From Tech Sheet W18494791, p.43:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (26)

CodeMeaning

F1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failure; failed calibration F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.

Service modes (3)

Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Service Diagnostics CycleWhile in standby mode, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1…

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass