Model reference
KitchenAid KDFE104DSS3
Dishwasher
13 documents79 error codes13 service modes
Available documentation
Service Manual
- jobaid w10573282120 pg
- 2013 Stainless Steel Tall Tub Dishwasher120 pg
- Dimension Guide2 pg
Tech Sheet
- Tech Sheet W10904613 RevB68 pg
- Tech Sheet12 pg
- Tech Sheet12 pg
- KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
- Fiche technique W10751168C16 pg
Wiring Diagram
- KDTE204ESS4 Wiring Diagram W10921454 RevA2 pg
Service Flash
- Technical Service Pointer - W11753104 - Stainless Steel Dishwasher Models False F10E5 Error6 pg
Tech Tip
- Instruction Sheet2 pg
Installation Guide
- Installation Instructions76 pg
Other
- Service Pointer - W11807380 - Rev A - Service Tool 2.0 Bluetooth Connection6 pg
MyPros+ Max
Diagnose your KitchenAid KDFE104DSS3.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (79)
CodeMeaning
1-1Control detected K1 pilot relay stuck closed.1-2Control software issue10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2No response from User Interface (UI)3-1Thermistor/OWI open3-2Thermistor/OWI shorted3-3Thermistor/OWI failed calibration4-3Wash motor not running5-1Door switch stuck open5-2Door switch stuck closed6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Incoming water under 84°F (29°C)6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disc missingF1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…View all 79 error codes
F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F10E1Dispenser electrical problemF10E2Vent wax motor electrical problemF10E3Drying fan errorF1E1Control detected K400 pilot relay stuck closed.F1E2Damaged or corrupted memory on control board; incompatible software components…F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failure; failed calibrationF3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…F3E3OWI calibration failure.F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F4E4Wash motor failure due to loose connection in wash motor circuit and/or open…F5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F5E1Door was not latched within 3 seconds of pressing Start/Resume, or loose…F5E2Control suspects door switch is stuck closed; control programmed to not start…F6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F6E1Low or no water (mechanical problem)F6E2Fill valve electrical problemF6E3Suds/air in pumpF6E4Float switch openF6E6Cool waterF7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F7E1No heatF7E2Heater stuck onF8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F8E1Slow drainF8E4Drain motor electrical problemF9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.F9E1Diverter can't find positionF9E2Diverter stuck onF9E3Diverter disc missingF9E4Lower spray arm error
Service modes (13)
- Beeper On/Off TogglePress and hold Hi Temp key for 3 seconds (tone sounds).
- Clear Customer Error HistoryDuring Service Diagnostic Cycle Interval 4, press HI TEMP key to clear customer error history.
- Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
- Control LockPress and hold Control Lock key for 5 seconds to turn On/Off.
- Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
- Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
- Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Rapid Advance ModeAfter starting a cycle, press HI TEMP
- Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Rapid Advance Mode (during normal cycle)Press HI TEMP
- Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
- Service Diagnostic CycleWhile in Standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
- Service Diagnostics Cycle["Press Start key to wake up the control panel.","Press any 3 keys in the sequence…
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass