mypros+
Model reference

KitchenAid KDFE104DSS4

Dishwasher

11 documents53 error codes9 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10880571 - Rev A (FR)16 pg
    Covers this model
  • KDTE104ESS3 Tech Sheet12 pg
    Covers this model
  • Tech Sheet W10904613 RevB68 pg
    Covers this model
  • Tech Sheet12 pg
    Covers this model
  • KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
    Covers this model

Service Manual

  • Dimension Guide2 pg
    Covers this model

Wiring Diagram

  • KDTE204ESS4 Wiring Diagram W10921454 RevA2 pg
    Covers this model

Service Flash

  • Technical Service Pointer - W11753104 - Stainless Steel Dishwasher Models False F10E5 Error6 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model

Installation Guide

  • Installation Instructions76 pg
    Covers this model

Other

  • Service Pointer - W11807380 - Rev A - Service Tool 2.0 Bluetooth Connection6 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KDFE104DSS4.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (53)

CodeMeaning
1-1Control detected K1 pilot relay stuck closed.1-2Control software issue10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2No response from User Interface (UI)3-1Thermistor/OWI open3-2Thermistor/OWI shorted3-3Thermistor/OWI failed calibration4-3Wash motor not running5-1Door switch stuck open5-2Door switch stuck closed6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Incoming water under 84°F (29°C)6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disc missingF1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…
View all 53 error codes
F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failure; failed calibrationF4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.

Service modes (9)

  • Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
  • Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
  • Demonstration Mode DeactivationRun the Service Diagnostic Program to deactivate demonstration (showroom) mode.
  • Error Code History RetrievalSame as Service Diagnostic Program entry (1-2-3-1-2-3-1-2-3 key sequence)
  • Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Service Diagnostic CycleWhile in Standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Service Diagnostic ProgramIn standby mode
  • Service Diagnostics Cycle["Press Start key to wake up the control panel.","Press any 3 keys in the sequence…

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass