Model reference
KitchenAid KDFE104DBL2
Dishwasher
15 documents52 error codes14 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10750906 - Rev A (FR)_W1075090616 pg
- Fiche technique16 pg
- Tech Sheet W10750905A12 pg
- Tech Sheet - W10750905 Rev A (EN)12 pg
- Tech Sheet12 pg
- Tech Sheet12 pg
- KDFE104DSS2 Tech Sheet W10751166 Rev C12 pg
- Fiche technique W10751168C16 pg
Service Manual
- Dimension Guide2 pg
Service Flash
- Technical Service Pointer - W11753104 - Stainless Steel Dishwasher Models False F10E5 Error6 pg
Tech Tip
- Instruction Sheet2 pg
Installation Guide
- Instruction Sheet1 pg
- Instruction Sheet2 pg
- Installation Instructions76 pg
Other
- Service Pointer - W11807380 - Rev A - Service Tool 2.0 Bluetooth Connection6 pg
MyPros+ Max
Diagnose your KitchenAid KDFE104DBL2.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (52)
CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection/component…3-3OWI calibration failure4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…5-1Door stuck open5-2Door stuck closed6-1Low/no water6-2Fill valve electrical problem6-3Suds or air in pump6-4Float switch open6-6Incoming water under 84°F (29°C)6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk missingF1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.View all 52 error codes
F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failure; failed calibrationF4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing Start/Resume…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Low/no water (mechanical problem); no water to dishwasher, water captured by…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Disconnected or damaged flowmeter.F6-E8Regen valve electrical problem; loose connection in regen valve circuit and/or…F7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control is faulty.F8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain motor stuck on; drain motor drive circuit on the control is faulty.F9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control is faulty.F9-E3Control detected diverter disk in sump is missing.
Service modes (14)
- Beeper On/Off TogglePress and hold Hi Temp key for 3 seconds (tone sounds).
- Buzzer Enable/DisablePress and hold the HI TEMP key for 3 seconds (a beep will sound).
- Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22-20), press the HI…
- Clear Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
- Control LockPress and hold the Control Lock button for 5 seconds to activate or deactivate.
- Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
- Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
- Demo Mode (Sales Display) DeactivationRun the service diagnostic program to deactivate demo mode.
- Rapid Advance (Customer Cycle)After starting a customer cycle, press HIGH TEMP
- Rapid Advance (Customer Cycles)["Start a customer cycle.","Press HIGH TEMP
- Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
- Service Diagnostic Program1
- Service Diagnostics Cycle["Press Start key to wake up the control panel.","Press any 3 keys in the sequence…
Full entry steps, exit procedures, and test sequences are available in Max.
Related KitchenAid dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass