mypros+
Model reference

KitchenAid KESH307HBL5

Range

6 documents55 error codes19 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 97822456 pg
    Covers this model
  • TECH SHEET - KitchenAid Range KESH307HBS68 pg
    Covers this model

Service Manual

  • KitchenAid Electronic Range Controls "B" & "D" Line Wall Ovens Job Aid93 pg
    Covers this model

Wiring Diagram

  • KitchenAid Range KESC307HWH5 Wiring Sheet1 pg
    Covers this model

Installation Guide

  • Installation Instructions5 pg
    Covers this model

Other

  • 431716993 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KESH307HBL5.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (55)

CodeMeaning
F0 E0No fault found.F1 E0EEPROM read fault (silent fault, not displayed).F1 E1EEPROM checksum does not match at start key (silent fault, not displayed).F1 E2Lost communication with power board.F1 E3Configuration jumper changeF1 E4Q8 shorted.F1 E5Meat probe not calibrated.F1 E6Display board EPROM access failure.F1 E7Power board EPROM access failure.F1 E8Improper keypad feedback from power board supply lift.F1 E9Stack overflow, highest priority fault.F1 EAExceeded stack warning level.F1E0EEPROM read fault (silent fault, not displayed).F1E1EEPROM checksum does not match at start key (silent fault, not displayed).F1E3Configuration jumper changeF1E4Q8 shorted.F1E9Stack overflow, highest priority.F2 E0Cancel key level too low (open).F2 E1Cancel key invalid.F2 E2Cancel key loop test failed.F2 E3Key held down too long or keyboard short.F2 E4Keys unsettled, probably due to noise.F2E0Keypad switch assembly misconnected to control.F2E2Cancel key loop test failed.F2E3Key held down too long or keyboard short.F2E4Keys unsettled, probably due to noise.F2E5Cancel key failed.F3 E0Oven temperature sensor (PLAT sensor) open.F3 E1Oven temperature sensor (PLAT sensor) shorted.F3 E2Oven temperature too high (runaway).
View all 55 error codes
F3 E3Shorted oven sensor.F3 E4Oven temperature too high (runaway condition).F3E0Oven sensor open.F3E1Oven sensor shorted.F3E2Oven temperature too high (runaway).F4 E0Meat probe shorted (less than 1500 ohms).F4 E1Meat probe shorted (less than 1500 ohms).F4E1Meat probe shorted (less than 1500 ohms).F5 E1Self-clean latch will not make after 30 seconds.F5 E3Loss of 120 VAC across L1 to ground, or Q19 circuit error.F5 E5Self-clean temperature not satisfied after 30 minutes.F5 E6Door locked with door open.F5 E7Door unlocked and will not unlatch.F5E0Door locked somehow with door open.F5E1Self clean latch lock make after 30 seconds.F5E3Loss of 120 VAC across L1 to ground or Q19 circuit error.F5E5Self clean temperature not satisfied after 30 minutes.F5E6Door locked somehow with door open.F5E7Door unlocked somehow and will not unlatch.F6 E0Ambient sensor opened (too hot).F6E0Ambient (console bi-metal) sensor opened (too hot).F7 E0Input switches will not follow their strobe level (shorted to ground).F7 E1Invalid door switch reading.F7E0Input switches won't follow their strobe level (shorted to ground).PFPower failure (not a failure of control).

Service modes (19)

  • Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
  • End of Service Test Sequence (Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • End of Service Test Sequence (Non-Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • F1E3 Configuration Reset / Timer ID Verification["Make sure harness to P1 connector is correct per wiring diagram.","Step 1
  • Hidden Functions - Bake Temperature CalibrationTouch and hold the Bake keypad for 5 seconds.
  • Hidden Functions - Clock Display OffTouch and hold the Clock keypad for 5 seconds.
  • Hidden Functions - DehydrateTouch and hold the Conv
  • Hidden Functions - End-of-Cycle Tones OffTouch and hold the Cook Time keypad for 5 seconds.
  • Hidden Functions - Fahrenheit/Celsius ToggleTouch and hold the Broil keypad for 5 seconds.
  • Hidden Functions - Keypad Entry Tones OffTouch and hold the Stop Time keypad for 5 seconds.
  • Hidden Functions - Keypad LockoutTouch and hold the #3 keypad for 5 seconds.
  • Hidden Functions - Last F/E Code and ROM RevisionTouch and hold the #0 keypad for 5 seconds.
  • Hidden Functions - Raising Bread DoughTouch and hold the Baked Goods keypad for 5 seconds.
  • Hidden Functions - Range Configuration DisplayTouch and hold the #1 keypad for 5 seconds.
  • Hidden Functions - Sell ModeTouch and hold the Timer Cancel keypad for 5 seconds.
  • Hidden Functions - Timer Operating Tones OffTouch and hold the Timer Start keypad for 5 seconds.
  • Hidden Functions - Tone Frequency ChangeTouch and hold the #7 keypad for 5 seconds.
  • Non-Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
  • Sabbath Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass