mypros+
Model reference

Magic Chef 11GY-1K

Range

2 documents81 error codes17 service modes

Available documentation

Tech Sheet

  • Service Technical Sheet16 pg
    Covers this model
  • Tech Sheet - 818227716 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef 11GY-1K.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (81)

CodeMeaning
dLDoor lock errordUDoor unlock errorE3The heater cannot warm the water to the desired temperature within 90 minutes…E6NTC open circuit failure (only alarmed during on-line test).E7NTC short circuit failure (only alarmed during on-line test).F/02Long drain timeF/05Water temperature sensor (NTC) value is out of range during the water heating…F/06Drive motor tachometer errorF/07Motor Control Unit (MCU) short circuit detected by the main control; if failure…F/09Overflow conditionF/10MCU thermal protector tripF/11Serial communication errorF/13Dispenser system errorF/14EEPROM errorF/15Motor Control Unit errorF/21CCU/touchpad-LED assembly communication errorF/22CCU/touchpad-LED assembly communication errorF/COMSerial communication errorF/CWLoad detected in drum at start of Clean Washer cycle (detection by weight).F/dLDoor lock errorF/DSDoor switch errorF/DSPDispenser system errorF/dUDoor unlock errorF/EPump driver fails to activate, one of the main relays is not working properly…F/HNo water detected entering the machine or no pressure switch trip detected…F/H2ONo water detected entering machine or pressure switch trip not detected…F/HEWater heating errorF/MCUMCU thermal protector tripF/NTCWater temperature sensor (NTC) errorF/OFLOverflow condition
View all 81 error codes
F/PMPPump drive system errorF/SPDMotor speed detection errorF0-E0Default F codeF01Pump driver fails to activate, one of the main relays is not working properly…F06Motor Control Unit (MCU) has an internal failureF1-E0Electronic control malfunction (E0, E1, & E2 variants).F1-E1Electronic control malfunction (E0, E1, & E2 variants).F1-E2Electronic control malfunction (E0, E1, & E2 variants).F2Membrane switch (touch panel) failure.F2-E0Keypad keytail not connected.F2-E1Key held down too long, or key is shorted.F2-E3Electronic control malfunction (E3, E4, & E5 variants).F2-E4Electronic control malfunction (E3, E4, & E5 variants).F2-E5Electronic control malfunction (E3, E4, & E5 variants).F20No water detected entering machine or pressure switch trip not detectedF21Long drainF22Door lock errorF23Water heater failureF24Water temperature sensor (NTC) errorF25Motor speed detection errorF26Door switch errorF27Overflow conditionF28Serial communication errorF3-E0Temperature sensor opened (lower cavity).F3-E1Temperature sensor shorted (lower cavity).F3-E2Temperature sensor opened (microwave).F3-E3Temperature sensor shorted (microwave).F31Door unlock errorF33Dispenser system errorF35MCU over-temperature errorF3HHumidity sensor out of range.F40Pump drive system errorF42Load detected in drum at start of Clean Washer cycle (detection by weight).F5-E0Lower cavity over temperature while cleaning.F5-E3Microwave cavity over temperature during cooking.F6Microwave relay failure.F6-E0Self-clean latch will not lock.F6-E1Self-clean latch will not unlock.F8-E0Oven over temperature while door open and latch lock.F8-E1Oven over temperature while door open and latch unlock.F8-E2Oven over temperature while door close and latch unlock.F8-E3Oven over temperature while door close and latch unlock (E3 variant).F8-E4Oven over temperature while door close and latch unlock (E4 variant).MCUMotor Control Unit has internal failure; if failure occurs during high-speed…Memory FailureControl board memory/software failure detected during Field Service Test…Motor high currentMotor drawing excessive current detected during Field Service Test, indicated…Motor low currentMotor drawing insufficient current detected during Field Service Test…SdSuds lockSudExcessive suds detectedThermistor failureThermistor failure detected during Field Service Test, indicated by Heavy Wash…Turbidity Sensor failureTurbidity sensor failure detected during Field Service Test, indicated by Rinse…

Service modes (17)

  • Bake Temperature Offset Adjustment1
  • Child Lock["Ensure the microwave oven and Timer are off.","Touch and hold CANCEL for 5 seconds until 2 tones…
  • Demo Mode["Microwave oven and Timer must be off.","Touch and hold Timer for 5 seconds until two tones sound…
  • diagnostic["Ensure washer is empty and control is in OFF state.","Close the door.","Push CONTROL/ON (if…
  • Fahrenheit to Celsius Conversion1
  • Field Service TestPress the Heavy Wash key 5 times followed by the Start key within 6 seconds.
  • Manual Diagnostic Test["Washer must be empty and control must be in OFF state.","Close the door.","Select any one key…
  • Manual Function TestPress the Normal Wash key 5 times followed by the Start key within 6 seconds
  • On-Line Check Mode (Service Diagnostics Cycle)1
  • Quick Diagnostic Test (bypassing Service History)["Drum must be empty.","Close the door.","Push POWER.","Select the CLEAN WASHER cycle.","Press…
  • Quick Entry Diagnostic Test (bypassing Service History Mode)["Ensure drum is empty.","Close the door.","Push POWER.","Select the CLEAN WASHER cycle.","Press…
  • Sabbath Mode ExitIf 'SAB' appears in the digital display, the oven is in Sabbath Mode.
  • Sales Floor Demo ModePress Extra Rinse keypad 5 times within 6 seconds.
  • Service History Mode & Diagnostic Test["Washer must be empty and control must be in OFF state.","Close the door.","Select any one key…
  • Service Mode (Keypad/LED Test)Close the door, then within 60 seconds press RINSE ONLY and START/RESUME
  • Touch Panel and Electronic Control Diagnostic Test["Press and hold CANCEL while opening the door.","While still holding the CANCEL button, unplug the…
  • Touch Panel and Electronic Control Self-Diagnostic Test["Press and hold CANCEL while opening the door.","While still holding the CANCEL button, unplug the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax