Model reference
Maytag MHW8630HW2
Washer
13 documents29 error codes5 service modes
Available documentation
Tech Sheet
- Tech Sheet - W11156990 - Rev C_W1115699052 pg
- Tech Sheet W11156990 Rev B52 pg
- Tech Sheet W11417646 RevA52 pg
Service Manual
- Service Manual Whirlpool & Maytag 27" Front-load Washers94 pg
Service Flash
- Technical Service Pointer - Optimal Dispense Dosing Improvement3 pg
- Service Pointer - W11685325 - Rev A - Maytag Front Load Washers Squeaking Dampers3 pg
- 27" Front Load Washer Unresponsive Unit6 pg
- Service Pointer - W11401418 - Rev C - 27 Front Load Washer Long Cycle6 pg
- Technical Service Pointer6 pg
- Technical Service Pointer3 pg
Training
- Training Manual Service Tool31 pg
Other
- Service Pointer - W11504923 - Rev A - 27 Front Load Washer Dispenser Water Remaining3 pg
Installation Guide
- Installation Pointer - W10608624 - Drain Hose Installation6 pg
MyPros+ Max
Diagnose your Maytag MHW8630HW2.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (29)
CodeMeaning
F0E1Load detected in drum during Clean Washer cycle.F0E2Excessive suds detected in washer; washer is running a suds reduction routine.F0E4High temperature error during wash cycle.F0E5Off balance load detected.F12E0Communication between the Human Machine Interface and Wi-Fi Module has not been…F1E1Main relay open or shorted.F1E2MCU over- or under-voltage error.F3E1Pressure sensor signal missing or out of range.F3E2Wash NTC (thermistor) open or shorted.F3E6Accelerometer error.F4E1Wash heater relay error or no feedback signal; ACU cannot detect temperature…F4E2Heating timeout.F5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6E1No communication from the HMI detected by ACU.F6E2No communication from the ACU detected by the HMI.F6E3No communication from the MCU detected by the ACU.F7E10Motor disconnected error.F7E12MC/MCU overload.F7E2MC/MCU over temperature error or over current error/internal failure.F7E8MC/Motor over temperature error.F7E9Motor will not turn (locked rotor).F7EAMotor disconnected error (alternate display F7E10).F7ECMC/MCU overload (alternate display F7E12).F8E1Water inlet valve failure.F8E3Overflow condition detected.F9E1Long drain time.FCE0Communication between the Human Machine Interface and Wi-Fi Module has not been…Service modes (5)
- Fault/Error Code DisplayEnter Service Diagnostic Mode; the most recent fault code is shown automatically upon entry
- Human-Machine Interface TestFrom within Service Diagnostic Mode, press and release the 1st button used to activate Service…
- Quick Diagnostic TestFrom within Service Diagnostic Mode, press and release the 2nd button used to activate Service…
- Service Diagnostic Mode1. Washer must be in standby mode (plugged in, all indicators off). 2. Wait 30 seconds after…
- Software Version DisplayFrom within Service Diagnostic Mode, press and hold the 2nd button used to activate Service…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Maytag washer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass