Model reference

Maytag MHWE250XL00

Washer

10 documents69 error codes11 service modes

Available documentation

Tech Sheet

Tech Sheet W10252711 Rev A16 pg
Covers this model
Tech Sheet - W10252711 - Rev A16 pg
Covers this model
Tech Sheet W10207733 Maytag Epic Z Washer MHWZ600TW0116 pg
Covers this model

Service Manual

Epic Front-Loading Automatic Washer Technical Education Job Aid88 pg
Covers this model
Epic Front-Loading Automatic Washer88 pg
Covers this model
Maytag Epic with Oxi/prewash Option / Maytag Epic Z2 pg
Covers this model
Technical Education Job Aid 8178604 ML-1 Front-loading Automatic Washer88 pg
Covers this model
TECHNICAL EDUCATION JOB AID 8178686 ML-8 FRONT-LOADING WASHER EPIC z™96 pg
Covers this model

Service Flash

Technical Service Pointer W10539798 Clothes Damage3 pg
Covers this model

Quick Reference

Quick Reference Manual2 pg
Covers this model

MyPros+ Max

Diagnose your Maytag MHWE250XL00.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Washer

F/02 on my Maytag MHWE250XL00

M+

Long drain - drain time exceeds eight

From Tech Sheet W13150447, p.19:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drain pump winding resistance at connector J7. Expected: 12 to 16 ohms at room temperature.

3.Verify the board switches the pump at 120 VAC during the drain cycle.

Part W10876537

Drain pump assembly

Error codes (69)

CodeMeaning

F/02Long drain F/05Water temperature sensor (NTC) value is out of range during the water heating…F/06Drive motor tachometer error F/07Motor Control Unit (MCU) error F/09Overflow condition F/10Motor Control Unit (MCU) heat sink thermal trip F/11Serial communication error F/13Dispenser circuit error F/14EEPROM error F/15Motor Control Unit (MCU) error F/21CCU / Touchpad / LED assembly error F/22CCU / Touchpad / LED assembly error F/dLDoor lock error F/dUDoor unlock error F/HNo water detected entering machine or pressure switch trip not detected after…F01EEPROM error F02Pump drive error F03Main relays error F11Motor Control Unit has internal failure; repeating under or over voltage, or…F1E1Pump driver fails to activate, one of the main relays is not working properly…F1E2Motor Control Unit (MCU) has internal failure F2Motor Control Unit (MCU) has an internal failure; if failure occurs during…F20No water detected entering machine or pressure switch trip not detected F21Long drain F22Door lock error F23Heater failure F24Water temperature sensor error F25Drive motor tachometer error F26Door lock error F27Water heater error

View all 69 error codes

F28Water temperature sensor (NTC) error F29Door unlock error F2E1No water detected entering washer or pressure switch trip not detected F2E3Long drain F30Motor drive error F31Door switch error F32Load detected in drum at start of CLEAN WASHER cycle (detection by weight).F33Dispenser system error F34Door unlock error F35Overflow condition F3E1Heating element error F3E2Water temperature sensor (NTC) error F3E3Overflow condition F40Drain pump connection lost during the drain cycle F42Serial communication error F5Pump driver fails to activate, one of the main relays is not working properly…F52MCU heatsink overtemperature error F5E1Door switch error F5E2Door lock error F5E3Door unlock error F5E4Water heating element error F5E5Door switch error F5E6Door unlock error F6E1Serial communication error F6E2MCU failure F7E1Motor speed sensing error F7E2Serial communication error F7E5Serial communication error F7E6MCU failure F7E7Drain pump connection lost during cycle drain.F8No water detected entering machine or pressure switch trip not detected…F8E1Overflow condition F8E2Drain pump connection lost during cycle drain.F8E3Load detected in drum at start of CLEAN WASHER cycle (detected by weight).F9E1Long drain F9E2Drain pump connection lost during cycle drain.rLLoad inside drum during cleaning washer cycle SdSuds lock SudSuds lock condition detected

Service modes (11)

Automated Diagnostic Test["Enter Service History Mode & Diagnostic Test first.","Momentary press of the 2nd key to activate…
Clear Error Codes["Enter Service History Mode & Diagnostic Test first.","Press and hold the 3rd key for 5 seconds."]
Diagnostic Test["Washer must be empty and control must be in the OFF state.","Close the door.","Push CONTROL/ON…
Error Code Display/Navigation["Enter Service History Mode & Diagnostic Test first.","Momentary press of the 3rd key to display…
Error Code Navigation["Enter Service History Mode & Diagnostic Test first.","Momentary press of the 3rd key to display…
Manual Diagnostic Test["Ensure washer is empty and control is in the OFF state.","Close the door.","Select any one key…
Quick Diagnostic Test (Bypass Service History)["Ensure drum is empty.","Close the door.","Push POWER.","Select the CLEAN WASHER cycle.","Press…
Quick Diagnostic Test (bypasses error history)1
Quick Entry Diagnostic Test (bypassing Service History)1
Service History Mode & Diagnostic Test["Ensure washer is empty and control is in the OFF state.","Close the door.","Select any one key…
User Interface Test["Enter Service History Mode & Diagnostic Test first.","Momentary press of the 1st key to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass