Model reference
Whirlpool WDF530PLYW5
Dishwasher
12 documents29 error codes12 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10580729 - Rev B (FR)_W1058072916 pg
- Tech Sheet - W10580720 - Rev B12 pg
- Whirlpool Dishwasher WDF530PLYW0 Tech Sheet2 pg
Service Manual
- Global Wash System 2011 Undercounter Dishwashers Technical Education98 pg
Bulletin
- Whirlpool Dishwasher Global Wash System Service Update10 pg
Service Flash
- Remove & Install Door Panel/console Ass'y3 pg
- TESTING THE GWS WASH MOTOR - Technical Service Pointer W105089109 pg
- PLASTIC TALL TUB UNDERCOUNTER DISHWASHER Metal Strike Plate and Door Seal Kit3 pg
Tech Tip
- Instruction Sheet2 pg
Installation Guide
- Installation Instructions48 pg
- Instruction Sheet for Heater Element kit2 pg
Other
- W10460578B9 pg
MyPros+ Max
Diagnose your Whirlpool WDF530PLYW5.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (29)
CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Software or hardware incompatibility problem with control10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2Shorted key or short circuit(s) in keypad or in control's input lines that read…3-1Open connector or component in Temperature Sensing Circuit, open or faulty…3-2Incoming water temperature above 75°C (167°F), shorted connection or component…3-3OWI soil sensor failure.4-3Control canceled cycle due to error detected with wash motor.5-1Door switch stuck open5-2Door switch stuck closed6-1Low or no water to dishwasher (mechanical problem).6-2Fill valve electrical problem.6-3Too many suds or air in pump.6-4Overfill float switch open6-6Incoming water too cold (under 84°F / 29°C).6-7Flowmeter problem6-8Regeneration valve electrical problem (water softener models).7-0Flow meter disconnected or damaged.7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain motor stuck on9-1Diverter cannot find position9-2Diverter stuck on9-3Diverter disk missing from sump.Service modes (12)
- buzzer_togglePress and hold the High Temp key for 3 seconds (a beep will sound).
- control_lock_togglePress and hold the Control Lock button for 5 seconds to activate or deactivate.
- customer_program_fast_forwardAfter starting a customer program, press HI TEMP
- diagnosticIn standby mode, press any 3 keys in sequence 1-2-3-1-2-3-1-2-3 with less than 1 second between…
- Error History ReadingEnter Service Diagnostics Cycle. Error codes are displayed in intervals 24 (Error 1
- error_history_clearDuring diagnostic interval 25, press the HI TEMP key to clear customer error history. The Hi Temp…
- Rapid Advance ModePress HI TEMP
- Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
- Rapid Advance Mode (in-cycle)After starting a cycle, press HI TEMP
- Service Diagnostic CycleRefer to Tech Sheet provided with the dishwasher for specific entry sequence
- Service Diagnostics - Error Code ReadingAfter entering Service Diagnostics Cycle
- Service Diagnostics Cycle1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass