Model reference

Whirlpool WDT710PAHW1

Name: Whirlpool WDT710PAHW1
Brand: Whirlpool

Dishwasher

7 documents52 error codes3 service modes

Available documentation

Tech Sheet

Tech Sheet26 pg
Covers this model
Tech Sheet - W11349311 - Rev A26 pg
Covers this model
Tech Sheet W10904613 RevB68 pg
Covers this model

Service Manual

Global Wash System 2011 Undercounter Dishwashers Technical Education98 pg
Covers this model

Service Flash

Service Pointer - W10460581 (Moisture Detected Inside Door Panels)2 pg
Covers this model
PLASTIC TALL TUB UNDERCOUNTER DISHWASHER Metal Strike Plate and Door Seal Kit3 pg
Covers this model

Other

W10460578B9 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WDT710PAHW1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dishwasher

1-1 on my Whirlpool WDT710PAHW1

M+

Control detected K1 pilot relay stuck

From Tech Sheet W13580102, p.34:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (52)

CodeMeaning

1-1Control detected K1 pilot relay stuck closed.1-2Control software issue 10-1Dispenser electrical problem 10-3Drying fan error 2-1Control detected stuck key(s) in keypad or keypad connection.2-2No response from User Interface (UI)3-1Thermistor/OWI open 3-2Thermistor/OWI shorted 3-3Thermistor/OWI failed calibration 4-3Wash motor not running 5-1Door switch stuck open 5-2Door switch stuck closed 6-1Inlet water low/no water (mechanical problem)6-2Fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 6-7Flowmeter disconnected or damaged.6-8Regen valve electrical problem; loose connection in Regen valve circuit, and/or…7-1No heat 7-2Heater stuck on 8-1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.8-2Drain motor electrical problem 8-3Drain stuck on 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disc missing F1-E1Control detected K2 pilot relay stuck closed.F1-E2Damaged or corrupted memory or control board; incompatible software components…F10-E1Dispenser electrical problem; loose connection in Dispenser circuit and/or open…F10-E3Drying fan error; loose connection in fan circuit and/or open fan motor.

View all 52 error codes

F2-E1Control detected stuck key(s) in keypad or keypad connection.F2-E2User interface cannot communicate with main control; loose user interface…F3-E1Open connector or component in Temperature Sensing circuit; open or faulty…F3-E2Shorted connection or component in Temperature Sensing circuit; shorted or…F3-E3OWI calibration failure; OWI failure or drain hose check valve not sealing.F4-E3Wash motor not running; loose connection in motor circuit and/or faulty wash…F5-E1Door stuck open; door was not latched within 4 seconds of pressing…F5-E2Door stuck closed; control programmed to not start if it suspects the door…F6-E1Inlet water low/no water (mechanical problem); no water to dishwasher, captured…F6-E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6-E3Suds/air in pump; too many suds, bowls/pots capturing wash water, water…F6-E4Float switch open; overfill switch stuck in overfill position and/or dishwasher…F6-E7Flowmeter disconnected or damaged.F6-E8Regen valve electrical problem; loose connection in Regen valve circuit and/or…F7-E1No heat; control programmed to disable heater due to detected water heating…F7-E2Heater stuck on; heater drive circuit on the control failed.F8-E1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.F8-E2Drain motor electrical problem; loose connection in drain motor circuit and/or…F8-E3Drain stuck on; drain motor drive circuit on the control failed.F9-E1Diverter can't find position; corroded or loose connection in diverter…F9-E2Diverter stuck on; diverter drive circuit on the control failed.F9-E3Diverter disk missing from sump.

Service modes (3)

Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Service Diagnostic CycleWhile in Standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass