Model reference

Whirlpool KFGD500EBL03

Range

6 documents32 error codes5 service modes

Available documentation

Tech Sheet

Wiring Diagram - W10694077 - Rev A2 pg
Covers this model
MGT8800FZ tech sheet64 pg
Covers this model

Service Flash

Moisture Escaping from Upper Oven3 pg
Covers this model

Installation Guide

Installation Instructions36 pg
Covers this model
Installation Instructions40 pg
Covers this model
Instruction Sheet1 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool KFGD500EBL03.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

C-81 on my Whirlpool KFGD500EBL03

M+

Over temperature on induction cooktop

From Tech Sheet W15337570, p.22:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (32)

CodeMeaning

C-81Over temperature on induction cooktop (Type 2 failure)C-82Over temperature on induction cooktop (Type 2 failure)C-83Induction cooktop temperature sensor stuck (Type 2 failure).F-12Induction cooktop coil under current (Type 1 failure, affects only one burner).F-21Induction cooktop supply power frequency error (Type 2 failure, affects all…F-25Stuck fan on Induction Power System (IPS)F-36Induction cooktop temperature sensor is not working (Type 1 failure).F-37Induction cooktop temperature sensor is not working (Type 1 failure).F-40Induction Power System (IPS) failure (Type 1 or Type 2).F-42Induction cooktop power supply issue (Type 2 failure).F-43Induction cooktop under voltage (Type 2 failure).F-47Power supply from Induction Power Control (IPC) to User Interface is missing…F-56Wrong or invalid configuration (Type 3 failure F-58Wrong or invalid configuration (Type 2 failure).F-60User Interface does not work (Type 3 failure F1E0EEPROM Communication Error F1E1Upper RTD Uncalibrated F1E2Lower RTD Uncalibrated F1E5Sensor Usage Out of Range F1E7PCB Thermistor Open or Shorted F1E9WIDE Queue Full F2E0Keypad Disconnected F2E1Stuck Keypad F2E2Cancel or Off Key Error/Warming Zone Off Keypad Error F3E0Main Sensor Open or Shorted (Upper)F3E1Main Sensor Open or Shorted (Lower)F5E0Door and Latch Switches Do Not Agree F5E1Latch Not Operating F6E0Lost WIDE Communication F6E1Over Temp Cook

View all 32 error codes

F6E2Over Temp Clean F9E0Miswired

Service modes (5)

Cooktop Controls Diagnostic ModePress any 3 different keypads in sequence
Oven Diagnostics ModePress CANCEL>CANCEL>START or OFF>OFF>ON within 5 seconds. Use TEMP/TIME +/- or More/Less or number…
Semi Automatic Test ModeEnter Diagnostics Mode, navigate to 'Semi Auto Test' using TEMP/TIME +/- or More/Less or 3/6…
Temperature CalibrationPress Settings or Options keypad until 'Temp Calib' is displayed
Test Mode (Relay Activation)Enter Diagnostics Mode (CANCEL>CANCEL>START or OFF>OFF>ON within 5 seconds). Navigate to 'Test…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass