Model reference

Whirlpool YKFID500ESS0

Name: Whirlpool YKFID500ESS0
Brand: Whirlpool

Range

7 documents33 error codes5 service modes

Available documentation

Tech Sheet

Tech Sheet - W10575968 - Rev B24 pg
Covers this model
Fiche technique - Tech Sheet W10587896 - Rev B24 pg
Covers this model
Wiring Diagram - W10694076 - Rev A2 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model

Installation Guide

Installation Instructions16 pg
Covers this model
Instruction Sheet1 pg
Covers this model
Instruction Sheet1 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool YKFID500ESS0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

C-81 on my Whirlpool YKFID500ESS0

M+

Over temperature on induction cooktop

From Tech Sheet W14512482, p.14:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (33)

CodeMeaning

C-81Over temperature on induction cooktop (Type 2 failure).C-82Over temperature on induction cooktop (Type 2 failure).C-83Temperature sensor stuck on induction cooktop (Type 2 failure).F-12Coil under current on induction cooktop F-21Supply power frequency error on induction cooktop F-25Stuck fan on Induction Power System (IPS), right or left side fan depending on…F-36Temperature sensor is not working on induction cooktop (Type 1 failure).F-37Temperature sensor is not working on induction cooktop (Type 1 failure).F-40Induction Power System (IPS) failure F-42Power supply issue on induction cooktop (Type 2 failure).F-43Under voltage on induction cooktop (Type 2 failure).F-47Power supply from IPC to User Interface is missing, or WIDE communication error…F-56Wrong or invalid configuration F-58Wrong or invalid configuration on induction cooktop (Type 2 failure).F-60User Interface does not work F1-E0EEPROM communication error (internal oven control failure).F1-E1Upper RTD uncalibrated (internal oven control failure).F1-E2Lower RTD uncalibrated (internal oven control failure).F1-E5Sensor usage out of range (internal oven control failure).F1-E7PCB Thermistor/Sensor open or shorted.F1-E9WIDE Queue full.F2-E0Keypad disconnected from oven control.F2-E1Stuck key on oven control keypad.F2-E2Stuck key on oven control keypad.F3-E0Main oven temperature sensor open or shorted (upper oven).F3-E1Main oven temperature sensor open or shorted (lower oven).F5-E0Door and door position switch(es) do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F6-E0Lost communications (oven control).F6-E1Over temperature during cook mode (runaway temp).

View all 33 error codes

F6-E2Over temperature during clean mode (runaway temp).F6-E3Over temperature in warming drawer (runaway temp).F9-E0Product is mis-wired.

Service modes (5)

Diagnostics Mode (Oven - MRC2 Control)Press CANCEL > CANCEL > START on the oven control
Faults View / Clear (Oven)1
Semi Automatic Test Mode (Oven)1. Enter Diagnostics Mode by pressing CANCEL>CANCEL>START. 2. Press TEMP/TIME '+' or '-' keypads…
Temperature Calibration (Oven)1
Test Mode (Oven - Manual Relay Activation)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass