mypros+
Model reference

Whirlpool YMIR8890AS0

Range

9 documents60 error codes28 service modes

Available documentation

Tech Sheet

  • Fiche technique - Tech Sheet W104413076 pg
    Covers this model
  • Tech Sheet - W10392955 - Rev A (MRC-FR)8 pg
    Covers this model
  • Tech Sheet - W10441306 - Rev A6 pg
    Covers this model
  • Tech Sheet - W10392954 - Rev A (MRC)8 pg
    Covers this model

Service Flash

  • Technical Service Pointer10 pg
    Covers this model

Tech Tip

  • Oven Cleaning Quick Reference Guide2 pg
    Covers this model

Installation Guide

  • Installation Instructions16 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model

Quick Reference

  • Quick Reference Manual2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool YMIR8890AS0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (60)

CodeMeaning
C-81Over temperature condition detected.C-82Over temperature condition detected.F-12Coil under current detected on a burner.F-12 E-12Coil under currentF-21Supply power frequency is incorrect.F-21 E-00Supply power frequency errorF-25Stuck fan on power control board (right or left side fan, depending on which…F-25 E-25Stuck fan on power control board (right or left side fan, depending on which…F-36Temperature sensor is not working.F-36 E-36Temperature sensor is not working (Type 1).F-37Temperature sensor is not working.F-37 E-37Temperature sensor is not working (Type 1).F-40Power control board failure.F-40 E-XXPower control board failure error where XX describes one of 13 possible causes…F-42Power supply issue detected.F-42 E-00Power supply error (Type 2).F-43 E-00Power supply error (Type 2).F-47Power supply from power control board to User Interface is missing, or WIDE…F-47 E-35Power supply from power control board to User Interface is missing, or WIDE…F-47 E-39Power supply from power control board to User Interface is missing, or WIDE…F-47 E-47Power supply from power control board to User Interface is missing, or WIDE…F-56Wrong or invalid configuration (User Interface).F-56 E-00Wrong or invalid configurationF-58Wrong or invalid configuration (power control board).F-58 E-58Wrong or invalid configuration (Type 2).F-60User Interface does not work.F-61Power control board does not work.F-81 E-00Over temperatureF-82 E-00Over temperatureF1 E0EEPROM communication error on the MRC2 oven control.
View all 60 error codes
F1 E5Oven control sensor out of range.F1 E7PCB thermistor open or shorted on the MRC2 oven control.F1 E9WIDE queue full on the MRC2 oven control.F1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7PCB thermistor open or shorted.F2 E0Keypad disconnected from the MRC2 oven control.F2 E1Stuck key detected on the MRC2 oven control keypad.F2 E2Cancel key error on the MRC2 oven control.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F3 E0Main oven temperature sensor open or shorted.F3 E2Warming drawer temperature sensor open or shorted.F3-E0Main oven sensor open or shorted.F3-E2Warming drawer sensor open or shorted.F5 E0Door and door position switch do not agree.F5 E1Door latch not functional (clean mode).F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F6 E0Right cooktop communication error.F6 E1Over temperature condition during cook cycle.F6 E2CleanF6 E3Over temperature condition in the warming drawer.F6 E4Left cooktop communication error.F6 E5Oven control communication error (from cooktop perspective).F6-E1Over temperature during cook mode.F6-E2Over temperature during clean mode.F6-E3Over temperature in warming drawer.F9 E0Mis-wired house or range detected.

Service modes (28)

  • Auto TestEnter diagnostic mode (CANCEL>CANCEL>START)
  • CONTROL RESETPress CANCEL > CANCEL > START to enter Service Mode
  • Diagnostics Mode (Auto Test)Press CANCEL > CANCEL > START
  • Diagnostics Mode for Cooktop Controls["Ensure that both cooktop (EGO) controls are OFF (idle mode).","Touch OFF>OFF>ON for the selected…
  • DISPLAYPress CANCEL > CANCEL > START to enter Service Mode
  • EGO Cooktop Control Diagnostics Mode["Ensure both cooktop (EGO) controls are OFF (idle mode)","Touch OFF > OFF > ON for the selected…
  • ENG MODEPress CANCEL > CANCEL > START to enter Service Mode
  • ENG MODE (Engineering Mode)Enter diagnostic mode (CANCEL>CANCEL>START), scroll to 'ENG MODE' (step 2)
  • FAULTSPress CANCEL > CANCEL > START to enter Service Mode
  • MRC Control Module Diagnostic ModePress CANCEL > CANCEL > START
  • MRC2 Diagnostics Mode (Auto Test)["Press CANCEL","Press CANCEL","Press START","Display shows 'TEST ON' with cavity temperature and…
  • MRC2 Service Mode - AUTO TEST["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'AUTO TEST'"]
  • MRC2 Service Mode - CONTROL RESET["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'CONTROL RESET'"]
  • MRC2 Service Mode - DISPLAY["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'DISPLAY'"]
  • MRC2 Service Mode - ENG MODE["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'ENG MODE'","Press START to…
  • MRC2 Service Mode - EXTERNAL FAULTS["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'EXTERNAL FAULTS'"]
  • MRC2 Service Mode - FAULTS["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'FAULTS'"]
  • MRC2 Service Mode - RELAY USAGE["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'RELAY USAGE'"]
  • MRC2 Service Mode - TEST MODE (Relay Checks)["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'TEST MODE'","Press designated…
  • MRC2 Service Mode - TEST ON (Relay Checks)["Press CANCEL","Press CANCEL","Press START","TEST ON is displayed upon entry","Press designated…
  • MRC2 Service Mode - USAGE["Press CANCEL > CANCEL > START to enter Service Mode","Scroll using up arrow/+ or 3 key to…
  • MRC2 Service Mode - VERSION["Press CANCEL > CANCEL > START to enter Service Mode","Scroll to 'VERSION'"]
  • Temperature AdjustmentPress OVEN LIGHT for 5 seconds
  • TEST MODEPress CANCEL > CANCEL > START to enter Service Mode
  • TEST ON (Relay Checks)Press CANCEL > CANCEL > START
  • TEST ON (Relay Control)Enter diagnostic mode (CANCEL>CANCEL>START)
  • USAGEPress CANCEL > CANCEL > START to enter Service Mode
  • VERSIONPress CANCEL > CANCEL > START to enter Service Mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass