mypros+
Model reference

Whirlpool W11416787

Washer

1 document34 error codes7 service modes

Available documentation

Service Manual

  • Technical Manual - Whirlpool® and Maytag® 4.7/5.3 Cubic Foot Top Load Washer88 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool W11416787.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (34)

CodeMeaning
F0E2Oversuds condition detected; suds prevent basket from spinning or pressure…F0E3Overload detected; load size exceeds washer capacity or basket cannot be turned.F0E4Spin limited by water temperature; water temperature is too high to spin at…F0E5Off balance load condition detected.F0E7Load detected in basket when Clean Washer cycle is selected.F0E8Water ring fault; too much residual water detected.F0E9Off balance pause; off balance condition detected after user interventions.F1E1Main control (ACU) fault detected.F1E2Motor drive module over voltage; main control detects a problem in the motor…F2E1HMI stuck button; user interface detects a button is continuously activated.F2E2HMI disconnected from the ACU.F3E2Pressure system fault; main control detects an out of range or absent pressure…F3E3Inlet water temperature fault; inlet thermistor detected open or shorted.F3E5Mini bulk system error; bulk level sensor signal detected out of range.F5E1Lid switch faultF5E2Lid lock will not unlock; excessive force on lid, wash media buildup, or main…F5E3Lid lock will not lock; obstruction or lid lock mechanism failure.F5E4Lid not opened between cycles; user presses START after a predetermined number…F6E1Communication errorF6E3Communication errorF7E1Tachometer missing or wrong signal; ACU cannot read speed or power from the…F7E2MCI drive failure; failure within the motor or ACU hardware.F7E3Basket engaged during wash; shifter is not disengaging basket for wash mode.F7E4Basket re-engagement failure; shifter not engaging basket for spin or…F7E6Motor circuit open; one or more motor lines detected open.F7E7Motor unable to reach target RPM.F7E8Motor drive module over temperature; main control detects a problem in the…F7E9Locked rotor; motor is not moving when actively being driven.F7EAMotor phase lost; one or more of three motor phases lost or under current…F8E1Long fill; water level does not change for a period of time or water is present…
View all 34 error codes
F8E2Dispenser system failure; bulk pump is on but current is outside of thresholds.F8E3Overflow or flood condition; main control senses water level that exceeds…F8E6Water hazard; water sensed in tub and lid left open for more than 10 minutes.F9E1Drain pump system problem

Service modes (7)

  • Component Activation["Enter Service Mode.","Navigate to Service Diagnostics.","Select Component Activation.","Use…
  • Diagnostic Cycle["Enter Service Mode.","Navigate to Service Diagnostics.","Select Diagnostic Cycle."]
  • DLMS Calibration Cycle["Enter Service Mode.","Navigate to Factory Diagnostics.","Select DLMS Calibration Cycle."]
  • Fault History["Enter Service Mode.","Navigate to Fault History.","Select to view stored fault codes."]
  • HMI Test["Enter Service Mode.","Navigate to Service Diagnostics.","Select HMI Test.","Select desired…
  • Sensor Feedback["Enter Service Mode.","Navigate to Service Diagnostics.","Select Sensor Feedback.","Use Left/Right…
  • Service Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass