mypros+
Model reference

Whirlpool WTW4950HW0

Washer

13 documents23 error codes18 service modes

Available documentation

Service Manual

  • Technical Manual Whirlpool® 3.8 cu ft Top Load Washer with Removable Agitator54 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W11447418 - Rev A2 pg
    Covers this model
  • Tech Sheet W10740624 Rev B44 pg
    Covers this model
  • Service Technical Sheet W1074057344 pg
    Covers this model
  • Diagnostic LED, Diagnostic Test Mode and Error Code summary sheet3 pg
    Covers this model

Service Flash

  • Technical Service Pointer - Stainless Basket Unbalance6 pg
    Covers this model
  • Service Pointer - W11787221 - Rev B - Top-Load Washer Control Board Housing Needs to be Replaced15 pg
    Covers this model
  • Service Pointer - W11648603 - Rev A - Top Load Washers Two-Step Start Behavior Change6 pg
    Covers this model
  • Service Pointer - W11766193 - Rev F - Top Load Washer and Stacked Laundry - F3E1 Pressure Sensor Error or Drain Pump Running Continuously9 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model
  • Technical Service Pointer - Noise During Spin6 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model

Other

  • Wtw5010lw0 owners-manual-w11436596-reva21 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW4950HW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (23)

CodeMeaning
F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Switch mismatch; the switches do not match the console or are not operating…F3E1Pressure system fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open, control not…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed fault; main control cannot determine speed of basket or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill / long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F8E6Hot and cold water supply lines are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (18)

  • AATCC Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Spin' LED is…
  • Calibration Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Rinse' LED is…
  • Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Dry Factory Diagnostics["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Factory Cal Test Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Factory Diagnostics Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes (entry sequence above).","Turn cycle selector knob until…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin & Done' LEDs are…
  • NVH Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Service Diagnostic Test ModeRefer to the Service Tech Sheet located inside the unit front top corner for the specific button…
  • Service Diagnostic Test Modes["After power is applied, wait 10 seconds before activating.","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse, Spin, and Done'…
  • SW Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Tachometer Verification["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are…
  • UI Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse & Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass