mypros+
Model reference

Whirlpool WTW4950HW2

Washer

14 documents22 error codes17 service modes

Available documentation

Service Manual

  • Technical Manual Whirlpool® 3.8 cu ft Top Load Washer with Removable Agitator54 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W11447418 - Rev A2 pg
    Covers this model
  • Service Technical Sheet W1074057344 pg
    Covers this model
  • Diagnostic LED, Diagnostic Test Mode and Error Code summary sheet3 pg
    Covers this model

Service Flash

  • Technical Service Pointer - Stainless Basket Unbalance6 pg
    Covers this model
  • Service Pointer - W11787221 - Rev B - Top-Load Washer Control Board Housing Needs to be Replaced15 pg
    Covers this model
  • Service Pointer - W11648603 - Rev A - Top Load Washers Two-Step Start Behavior Change6 pg
    Covers this model
  • Service Pointer - W11766193 - Rev F - Top Load Washer and Stacked Laundry - F3E1 Pressure Sensor Error or Drain Pump Running Continuously9 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model
  • Technical Service Pointer - Noise During Spin6 pg
    Covers this model
  • Technical Service Pointer - Pressure Dome Port Flash7 pg
    Covers this model

Quick Reference

  • Quick Start Guide2 pg
    Covers this model
  • Manual de referencia rapida1 pg
    Covers this model

Other

  • Wtw5010lw0 owners-manual-w11436596-reva21 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW4950HW2.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
F0E2Oversuds condition detected.F0E4High water temperature during rinse cycle, spin limited by water temperature.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault.F2E1Stuck button detected on user interface.F2E3Switch mismatch detected.F3E1Pressure system fault.F3E2Inlet water temperature fault.F5E1Lid switch fault.F5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cycles.F7E1Basket speed fault.F7E5Shifter fault.F7E6Motor fault.F7E7Motor unable to reach target RPM.F8E1Long fill or no fill condition.F8E3Overflow condition detected.F8E5Hot and cold inlet hoses are reversed.F8E6Hot and cold water supply lines are reversed.F9E1Long drain condition.

Service modes (17)

  • AATCC Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' LED is…
  • Calibration Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' LED is…
  • Dry Factory Diagnostics["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Factory Cal Test Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Factory Diagnostics Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Fault Code Display ModeEnter the fault code display mode separately after completing Test Modes (specific sequence in…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin & Done' LEDs are…
  • NVH Cycle["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Service Diagnostic Test ModeRefer to the Service Tech Sheet located inside the unit front top corner for the specific button…
  • Service Diagnostic Test Modes["After power is applied, wait 10 seconds before activating.","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse, Spin, and Done'…
  • SW Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Tachometer Verification["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs indicate mode…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass