mypros+
Model reference

Whirlpool WTW5057LW0

Washer

14 documents34 error codes12 service modes

Available documentation

Service Manual

  • TECHNICAL MANUAL Whirlpool® Top Load Washer156 pg
    Covers this model
  • TECHNICAL MANUAL Whirlpool® 2021 Top Load Washer150 pg
    Covers this model
  • TECHNICAL MANUAL Whirlpool® Top Load Washer144 pg
    Covers this model
  • Dimension Guide12 pg
    Covers this model
  • Technical Manual W11428632 REVA1 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W11428598 - Rev D2 pg
    Covers this model

Service Flash

  • Service Pointer - W11618678 - Rev A - Top Load Washers Cycle Won't Start3 pg
    Covers this model
  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Service Pointer - W11632927 - Rev I - Top Load Washer Will Not Run Cycle and/or GFCI Ground Fault Failure9 pg
    Covers this model
  • Technical Service Pointer #W11750573 Rev. B - Vertical Drain Pump Not Draining8 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model

Quick Reference

  • Manual de referencia rápida1 pg
    Covers this model
  • Quick Start Guide Whirlpool® Top Loading Washing Machine Operating Instructions2 pg
    Covers this model
  • Quick Start Guide2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW5057LW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (34)

CodeMeaning
F0E2Oversuds condition detectedF0E3OverloadF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F0E7Load detected when running Clean Washer cycleF0E8Water RingF0E9Off Balance PauseF1E1Main Control (ACU) fault detected.F1E2Motor drive module over voltage.F2E1HMI Stuck ButtonF2E2HMI Disconnected from the ACU.F2E3ACU/UI mismatch detected.F3E2Pressure System FaultF3E3Inlet water temperature fault.F5E1Lid Switch FaultF5E3Lid Lock Will Not UnlockF5E4Lid Not Opened Between CyclesF6E1Communication ErrorF6E3Communication errorF7E1Tachometer missing or wrong signalF7E2MCI drive failure.F7E3Basket Engaged During WashF7E4Basket Re-engagement FailureF7E6Motor Circuit OpenF7E7Motor unable to reach target RPM.F7E8Motor drive module over temperature.F7E9Locked rotor condition.F7EAMotor phase loss.F7ECMotor drive module over current/overload.F8E1Long Fill
View all 34 error codes
F8E3Overflow or Flood ConditionF8E6Water HazardF9E1Drain Pump System ProblemF9E9Wrong voltage detected.

Service modes (12)

  • Automatic Test["Enter Service Mode.","Press Key 2 and then Key 5."]
  • Automatic Test Mode["Activate Service Diagnostic Mode first.","Press and release Key 2.","Press Key 5/START to begin…
  • Clear Fault Codes1
  • Factory Calibration Cycle1. Washer in standby mode (plugged in, all LEDs off), lid closed. 2. Within 8 seconds
  • Factory Mode / Factory Calibration Cycle["Ensure washer is in standby mode (plugged in, all LEDs off) and lid is closed.","Within 8…
  • Fault Code Display Mode["Activate Service Diagnostic Mode first.","Press and release Key 3 to display the most recent…
  • Fault History["Enter Service Mode.","Press Key 3."]
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all LEDs off).","Within 8 seconds, perform the…
  • Service Mode Entry["Ensure washer is in standby mode (plugged in with all LEDs off).","Within 8 seconds, press and…
  • Software Version["Enter Service Mode.","Press Key 2 for 3 seconds."]
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold Key 2 for 5 seconds.","Display…
  • UI Test["Activate Service Diagnostic Mode first.","Press and release Key 1.","All LEDs flash once, then…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass