mypros+
Error code reference

Crosley Washer Error Code E75

Water temperature sensor circuit failure.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E75 error code actually means

Your Crosley washer is showing E75 because it detected a problem with the sensor that measures water temperature. The machine cannot confirm whether the water coming in is hot or cold, so it stopped the cycle to prevent potential issues. This is usually a problem with a small sensor inside the water valve or a wiring connection leading to it.

Diagnostic procedure

The full E75 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Refer to test (12) - check resistance of water valve NTC.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E75 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E75

Ranked by how often they cause this code
  1. 1Failed water valve NTC thermistor
  2. 2Damaged or broken wiring harness
  3. 3Corroded or loose connector pins
  4. 4Water valve assembly failure
  5. 5Faulty main control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E75

What does E75 mean on a Crosley washer?
E75 on a Crosley washer means the control board has detected a failure in the water temperature sensor circuit. This circuit relies on an NTC thermistor located in the water valve to measure incoming water temperature. When the sensor or its wiring sends a signal outside the expected resistance range, the washer stops and displays E75. Diagnosis starts with checking the resistance of the water valve NTC using a multimeter.
Is it safe to use my Crosley washer while E75 is showing?
It is not recommended to continue running the washer with an active E75 code. Without a functioning temperature sensor, the control board cannot regulate water temperature properly, which can result in incomplete cycles or incorrect wash conditions. Running cycles in this state could also mask further developing faults in the water valve or control system.
Will resetting my Crosley washer clear the E75 error code?
A power reset may temporarily clear the E75 code, but if the underlying fault in the NTC thermistor circuit still exists, the error will return once the washer runs again. Resetting without repairing the root cause does not fix the problem. A proper repair requires testing the water valve NTC resistance and addressing any wiring or component failures found during diagnosis.
Can I fix an E75 error on my Crosley washer myself?
A knowledgeable DIYer comfortable with basic electrical testing can diagnose this code by checking the NTC thermistor resistance and inspecting the wiring harness and connectors. If the sensor or water valve needs replacement, the repair involves disconnecting power, removing the water inlet valve, and installing the new part. If the fault traces back to the control board, that repair is more involved and may be better handled by a technician.
How much does it cost to repair an E75 error on a Crosley washer?
Repair costs depend on which component has failed. A water valve replacement, which is the most common fix, typically runs in the range of $60 to $180 including parts and labor depending on your location and service provider. If only a wiring repair or connector cleaning is needed, costs are generally lower. A control board replacement, if required, is the most expensive scenario and can range from $150 to $350 or more.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass