mypros+
Error code reference

Crosley Washer Error Code EB2

Incoming line voltage above 130 VAC.

Crosley codesCrosley washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the EB2 error code actually means

The EB2 code means your Crosley washer is detecting that the electricity coming from your wall outlet is at a higher voltage than it should be, which could damage the machine. The washer shuts itself down automatically to protect its parts. You should check the outlet voltage before running the washer again, and if the voltage looks normal, the control board inside the washer may need to be replaced.

Diagnostic procedure

The full EB2 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check voltage at outlet. If less than 130VAC, replace console control board.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock EB2 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of EB2

Ranked by how often they cause this code
  1. 1High utility supply voltage
  2. 2Faulty console control board voltage sensor
  3. 3Home wiring or panel issue
  4. 4Shared circuit voltage elevation

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about EB2

What does EB2 mean on a Crosley washer?
EB2 means the washer's control board has detected incoming line voltage above 130 VAC. The machine stops operation automatically to protect its components from damage caused by excessive voltage. The fault can be caused by a genuine overvoltage condition at the outlet or by a failing console control board that is misreading the voltage.
Is it safe to use my Crosley washer when the EB2 code is showing?
No, you should not run the washer while the EB2 code is active. If the voltage at your outlet truly exceeds 130 VAC, operating the machine risks damaging the motor, control board, and other internal components. Wait until the voltage issue is diagnosed and resolved before resuming use.
How much does it cost to fix a Crosley washer showing the EB2 error?
If the problem is a faulty console control board, parts and labor typically range from around $150 to $350 depending on your location and the service provider. If the fault is with your home's electrical supply, electrician fees to diagnose and correct wiring or transformer issues can vary widely, generally from $100 to $400 or more depending on the scope of work.
How do I fix the EB2 error on my Crosley washer?
Start by measuring the voltage at the outlet with a multimeter. If the reading exceeds 130 VAC, do not run the washer and contact a licensed electrician to address the supply voltage issue. If the outlet voltage is below 130 VAC and the code keeps appearing, the console control board needs to be replaced.
Will resetting my Crosley washer clear the EB2 error code?
A reset may temporarily clear the display, but the EB2 code will return if the underlying cause is not addressed. If your outlet voltage is above 130 VAC, the washer will detect the condition again as soon as it resumes monitoring. The fix requires either resolving the supply voltage problem or replacing the console control board.

Related Crosley washer error codes

All Crosley washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass