mypros+
Error code reference

Fisher & Paykel Washer Error Code 22

Phase 1

Fisher & Paykel codesFisher & Paykel washer codes

Phase 1: Display Module and Motor Controller running out of sequence.

First step from the service manual

Turn off at the wall and back on after 5 seconds. If fault persists disable auto restart and retest for new fault code.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 22.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 22 means on a Fisher & Paykel washer

Error code 22 on a Fisher & Paykel washer indicates a sequencing conflict between the Display Module and the Motor Controller. These two control boards communicate with each other continuously throughout the wash cycle, and they must operate in a coordinated, synchronized state. When the washer detects that these two modules are running out of sequence, it means the timing or communication handshake between them has broken down, causing the machine to fault out as a safety measure.

This type of sequencing fault most commonly results from a temporary communication dropout rather than an immediate hardware failure. Power fluctuations, brief electrical interruptions, or a corrupted initialization routine during startup can all cause the two modules to lose sync. This is why the first recommended diagnostic step is a full power cycle at the wall, allowing both modules to reinitialize from scratch after at least 5 seconds of being completely de-energized.

If the fault returns after the power cycle, the next step is to disable the auto restart feature and retest. This allows the machine to display any underlying fault code that may have been masked by the code 22. A persistent sequencing error points toward a failing communication pathway, a wiring harness issue between the boards, or a defective Display Module or Motor Controller that is unable to properly synchronize. Identifying whether a new fault code appears after disabling auto restart is critical to determining which component is responsible.

Source: manufacturer service documentation.

Common causes of 22

  1. 01

    Temporary communication dropout between modules

    Wiring / connection

    A brief power fluctuation or electrical interruption during operation can cause the Display Module and Motor Controller to lose synchronization. A full power cycle at the wall usually resolves this without any parts replacement.

  2. 02

    Corrupted startup or initialization sequence

    Wiring / connection

    If the washer was interrupted mid-cycle or powered off abruptly, the two control modules may fail to reinitialize in the correct order on the next startup. Cycling power at the wall resets both modules and typically clears this condition.

  3. 03

    Faulty or loose wiring harness between the Display Module and Motor Controller

    Wiring / connection

    A damaged, corroded, or loose connector on the communication harness between the two boards can cause intermittent or persistent sequencing faults. Inspect the harness and connectors for visible damage, corrosion, or poor seating.

  4. 04

    Defective Display Module

    Part replacement

    If the Display Module is failing, it may be unable to properly synchronize with the Motor Controller, causing a persistent code 22. Disabling auto restart and retesting to see if a new fault code appears can help confirm whether this module is the source of the fault.

  5. 05

    Defective Motor Controller

    Part replacement

    A Motor Controller that is failing or has developed an internal fault may be unable to respond to the Display Module in the correct sequence. This would typically produce a persistent code 22 or reveal an additional underlying fault code after auto restart is disabled.

See the test procedure for each cause

Frequently asked questions about 22

What does 22 mean on a Fisher & Paykel washer?
Error code 22 means the Display Module and Motor Controller are running out of sequence with each other. These two boards need to communicate in a synchronized way for the washer to operate, and the machine has detected a breakdown in that coordination. The washer stops itself when this happens to prevent further problems. In many cases, a simple power cycle at the wall clears the fault by allowing both modules to reinitialize together.
Will resetting my Fisher & Paykel washer clear error code 22?
A power reset is the recommended first step and it does resolve code 22 in many cases, particularly when the fault was caused by a temporary power fluctuation or a disrupted startup sequence. Turn the machine off at the wall, wait at least 5 seconds, then turn it back on. If the error returns, you will need to disable the auto restart feature and retest to uncover any underlying fault code driving the issue.
Is it safe to keep using my washer when error code 22 is showing?
The washer will typically stop operation when code 22 is active, so continued use is not possible until the fault is cleared. You should not attempt to force the machine to run while this fault is present. Addressing the root cause of the sequencing conflict first is important before resuming normal laundry cycles.
How much does it cost to repair a Fisher & Paykel washer with error code 22?
If a power reset clears the fault, there is no parts cost at all. If the wiring harness needs attention, repair costs are generally low. If a control board such as the Display Module or Motor Controller needs to be replaced, parts and labor costs can range from around $150 to $400 or more depending on the specific board, part availability, and local labor rates.
What should I do if error code 22 keeps coming back after resetting?
If code 22 returns after a power cycle, the next step is to disable the auto restart feature on the washer and run it again. This allows the machine to display any new or underlying fault code that may have been hidden behind the sequencing error. That secondary fault code will give a clearer picture of whether the problem is in the wiring, the Display Module, or the Motor Controller, and will guide the next diagnostic or repair steps.

Related Fisher & Paykel washer codes

All Fisher & Paykel washer codes
View all 175 Fisher & Paykel washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass