mypros+
Error code reference

Frigidaire Washer Error Code E25

Recirculation Pump Relay Sense failure.

Frigidaire codesFrigidaire washer codes

Recirculation Pump Relay Sense failure.

First step from the service manual

Check wiring between main board and pump (Refer to test 17).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E25.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E25 means on a Frigidaire washer

The E25 error code on a Frigidaire washer indicates a Recirculation Pump Relay Sense failure. This means the main control board has detected an abnormal condition in the relay circuit that controls the recirculation pump. The relay sense circuit allows the board to confirm whether the relay has properly opened or closed, and when the sensed state does not match the expected state, the board logs this fault and halts operation to prevent damage to downstream components.

The recirculation pump is responsible for drawing water from the tub and redirecting it back through the wash system to improve cleaning performance. When the relay controlling this pump fails to respond correctly, the board cannot confirm proper pump operation. The root cause is most often found in the wiring harness connecting the main board to the pump, which is why the first diagnostic step involves inspecting that wiring path (Test 17).

Common failure points include broken or corroded wiring, loose connector pins at the board or pump terminals, a failed relay on the main control board itself, or a shorted or open recirculation pump motor. Technicians should begin with a thorough visual and continuity check of the wiring harness before condemning the pump or the board, as wiring faults are the most frequent source of relay sense errors in this platform.

Source: manufacturer service documentation.

Common causes of E25

  1. 01

    Faulty or damaged wiring harness

    Wiring / connection

    Broken, pinched, or corroded wires between the main control board and the recirculation pump are the most common cause of this fault. Inspect the full harness run for chafing, burn marks, or loose connector pins at both ends.

  2. 02

    Loose or disconnected connector

    Wiring / connection

    A connector that has vibrated loose at the pump terminal or the board header can interrupt the relay sense signal. Check each connector for a firm, fully seated fit and inspect the pins for corrosion or spread contacts.

  3. 03

    Failed relay on the main control board

    Part replacement

    If the relay on the control board that switches power to the recirculation pump has failed internally, the board will detect the mismatch between commanded state and sensed state and trigger E25. This requires replacing the main control board.

  4. 04

    Shorted or open recirculation pump motor

    Part replacement

    A pump motor winding that has shorted or gone open circuit can cause abnormal current draw or no response on the relay sense line. Check the pump motor for continuity and compare resistance readings to specification.

  5. 05

    Damaged main control board

    Part replacement

    If the wiring and pump check out correctly, the main control board itself may have a failed sense circuit or damaged relay driver. Board-level damage can prevent accurate relay status detection even when all external components are functional.

See the test procedure for each cause

Frequently asked questions about E25

What does E25 mean on a Frigidaire washer?
E25 indicates a Recirculation Pump Relay Sense failure. The main control board monitors the relay that powers the recirculation pump and has detected that the relay's sensed state does not match what the board commanded. This fault stops the washer from operating until the underlying cause is resolved.
Can I fix E25 on my Frigidaire washer myself?
A knowledgeable DIYer can perform the first diagnostic steps, which involve inspecting and testing the wiring between the main control board and the recirculation pump. If the fault is a loose connector or a damaged wire, that repair is straightforward. However, if the main control board or the pump motor needs replacement, comfort with appliance disassembly and basic electrical testing is required.
Will resetting the washer clear the E25 error code?
A reset may temporarily clear the E25 code, but if the underlying wiring fault, relay failure, or pump problem has not been corrected, the code will return during the next wash cycle. A reset alone is not a fix and should only be used as part of confirming whether a repair was successful.
Is it safe to use my Frigidaire washer while E25 is displayed?
No, you should not continue running the washer while E25 is active. The recirculation pump relay fault means the board cannot confirm proper pump operation, and running the machine in this state could cause further damage to the pump, wiring, or control board. Resolve the fault before resuming normal use.
How much does it cost to repair a Frigidaire washer E25 error?
Repair costs vary depending on what has failed. If the issue is a wiring problem or a loose connector, costs may be minimal, covering only diagnostic time. Replacing the recirculation pump motor typically runs between $80 and $200 in parts, while a new main control board can range from $100 to $300 or more, plus labor if a technician is hired.

Related Frigidaire washer codes

All Frigidaire washer codes
View all 100 Frigidaire washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass