mypros+
Error code reference

Frigidaire Washer Error Code E11

Fill time too long

Frigidaire codesFrigidaire washer codes

Fill time too long – water tap closed, water flow rate too low, pressure sensor defective, inlet valve defective, or air tube kinked.

First step from the service manual

Check that all connectors are correctly inserted, then run the Diagnostic Cycle test and check if hot and cold inlet valves are working.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E11.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E11 means on a Frigidaire washer

The E11 error code on a Frigidaire washer indicates that the machine took too long to reach the required water level during a fill cycle. The washer's pressure sensor monitors water level by detecting air pressure changes in a tube connected to the tub. If the control board does not detect the expected pressure change within a set time window, it triggers E11 and halts the cycle. This protects the machine from running a wash cycle without adequate water.

The most common hardware causes fall into two categories: water supply issues and component failures. On the supply side, a closed or partially closed water tap, a kinked inlet hose, or clogged inlet valve screens can all restrict flow to a level the washer cannot compensate for. Low household water pressure is another frequent culprit, especially if multiple fixtures are running simultaneously. On the component side, a defective hot or cold inlet valve may fail to open fully or at all, preventing adequate fill regardless of supply pressure.

The air tube that connects the tub to the pressure sensor is also a known failure point. If this tube is kinked, cracked, or has a loose connection, the pressure sensor receives inaccurate readings and may report an incomplete fill even when water is present. A faulty pressure sensor itself can produce the same false reading. Proper diagnosis involves checking all water supply connections, inspecting the inlet valve solenoids for correct operation during a diagnostic cycle, and verifying the integrity of the air tube and pressure sensor circuit.

Source: manufacturer service documentation.

Common causes of E11

  1. 01

    Closed or restricted water supply tap

    Wiring / connection

    The hot or cold water shutoff valves behind the washer may be fully or partially closed. Check that both valves are turned completely open before any further diagnosis.

  2. 02

    Clogged inlet valve screens

    Wiring / connection

    Fine mesh screens inside the water inlet valve connections can collect sediment and mineral deposits over time, severely restricting flow. Remove the inlet hoses and inspect the screens for debris, cleaning or replacing them as needed.

  3. 03

    Defective water inlet valve

    Part replacement

    The hot or cold inlet valve solenoid may have failed and is not opening fully when energized. Running the built-in diagnostic cycle will test whether each valve activates correctly, helping isolate a faulty solenoid.

  4. 04

    Kinked or disconnected air tube

    Wiring / connection

    The air tube running from the tub to the pressure sensor can become kinked during installation or over time. A kink or loose connection causes the pressure sensor to misread the water level and trigger E11 even if water flow is normal.

  5. 05

    Defective pressure sensor

    Part replacement

    If the pressure sensor itself has failed, it will not accurately detect water level changes and will report an incomplete fill to the control board. This is typically diagnosed after ruling out all supply and tube issues.

See the test procedure for each cause

Frequently asked questions about E11

What does E11 mean on a Frigidaire washer?
E11 means the washer took too long to fill with water during a cycle. The control board monitors how long it takes to reach the required water level, and if that time limit is exceeded, it stops the cycle and displays E11. Causes range from a closed water tap or kinked hose to a failed inlet valve or pressure sensor.
How do I fix an E11 error on my Frigidaire washer?
Start by confirming both water supply valves behind the machine are fully open and that the inlet hoses are not kinked. Next, check the inlet valve screens for clogs and clear any debris. If the water supply looks normal, run the washer's diagnostic cycle to test whether the hot and cold inlet valves are opening correctly. If a valve or the pressure sensor is found to be defective, that component will need to be replaced.
Will resetting my Frigidaire washer clear the E11 error?
A reset may temporarily clear the E11 code, but it will return at the next fill cycle if the underlying problem has not been fixed. Address the root cause, whether that is a supply issue or a faulty component, before attempting another wash cycle. Simply resetting without repairs is not a long-term solution.
Is it safe to use my Frigidaire washer while the E11 code is displayed?
You should not continue running wash cycles while E11 is active. The washer has halted because it detected an insufficient water fill, and running a cycle without adequate water can put unnecessary stress on the motor and pump components. Resolve the fill issue before resuming normal use.
How much does it cost to repair an E11 error on a Frigidaire washer?
If the fix is simply opening a valve or clearing a clogged inlet screen, the repair costs nothing beyond your time. Replacing a water inlet valve typically runs between $25 and $80 for the part, with additional labor costs if a technician is hired. Replacing a pressure sensor is generally in a similar parts cost range of $20 to $60, depending on the specific model.

Related Frigidaire washer codes

All Frigidaire washer codes
View all 100 Frigidaire washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass