mypros+
Error code reference

Frigidaire Washer Error Code F2

PCB (main control board) failure.

Frigidaire codesFrigidaire washer codes

PCB (main control board) failure.

First step from the service manual

Check wiring; if wiring shows disconnection replace wiring, if wiring is correct replace PCB.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F2.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F2 means on a Frigidaire washer

The F2 error code on a Frigidaire washer indicates a failure within the PCB, or main control board. The main control board is the central processing unit of the washer, responsible for coordinating all machine functions including motor operation, water inlet valve control, drain pump activation, and cycle timing. When the board fails or loses communication integrity, the machine cannot safely or reliably execute wash cycles and will halt operation with this fault code.

The diagnostic process begins with a thorough inspection of the wiring harness connected to the main control board. Loose connectors, corroded terminals, pinched wires, or damaged insulation can all interrupt the electrical signals the board depends on to function. In many cases, a wiring fault mimics a board failure, so confirming wiring integrity is the critical first step before condemning the board itself.

If all wiring connections are secure and undamaged, the fault lies within the PCB itself. Control board failures can result from power surges, moisture intrusion, component-level failures on the board, or general wear over time. Once wiring has been ruled out as the cause, the main control board requires replacement. This is not a component that can typically be repaired at the component level in the field.

Source: manufacturer service documentation.

Common causes of F2

  1. 01

    Loose or disconnected wiring harness

    Wiring / connection

    Connectors to the main control board can loosen over time due to vibration from normal washer operation. Inspect all wiring harness plugs at the board for secure seating and signs of backing out.

  2. 02

    Corroded or damaged wiring terminals

    Part replacement

    Moisture inside the cabinet can corrode connector pins or wire terminals, increasing resistance or breaking continuity in the circuits feeding the control board. Look for green or white oxidation on terminals and brittle or cracked wire insulation.

  3. 03

    Failed main control board (PCB)

    Part replacement

    The board itself can fail due to power surges, heat stress, or component-level faults. If wiring checks out as intact and properly connected, the PCB must be replaced.

  4. 04

    Power surge damage

    Part replacement

    A voltage spike from the home's electrical supply can damage sensitive components on the control board. If the F2 error appeared after a power outage or surge event, board damage is a likely cause.

See the test procedure for each cause

Frequently asked questions about F2

What does F2 mean on a Frigidaire washer?
The F2 error code indicates a main control board (PCB) failure on a Frigidaire washer. The board is the central component that manages all washer functions, and when it fails or loses a critical wiring connection, the machine stops and displays this code. Diagnosis starts with inspecting the wiring harness before replacing the board.
Can I fix the F2 error myself?
A knowledgeable DIYer can start by checking all wiring harness connections at the main control board for looseness, corrosion, or visible damage. If a disconnected or damaged wire is found, repairing or replacing that wiring may resolve the error. If the wiring is intact, replacing the main control board requires basic appliance repair skills and comfort working with electrical components.
Will resetting my Frigidaire washer clear the F2 code?
A power reset, such as unplugging the washer for a few minutes, may temporarily clear the display, but it will not resolve the underlying fault. If the wiring is loose or the control board has failed, the F2 code will return once the machine attempts to operate. A proper diagnostic inspection is needed to address the root cause.
Is it safe to use my Frigidaire washer when it shows F2?
No, you should not continue using the washer while it displays the F2 error. The main control board manages critical functions including motor control and water flow, and operating the machine with a faulty board or compromised wiring could cause further damage or unpredictable behavior. Leave the washer off until the fault is diagnosed and repaired.
How much does it cost to fix an F2 error on a Frigidaire washer?
If the fix involves repairing or replacing a wiring harness, costs are generally lower, typically in the range of $50 to $150 depending on parts and labor. If the main control board requires replacement, parts and labor costs combined can range from $150 to $400 or more, depending on the specific model and service rates in your area. Getting a diagnostic visit from a technician will give you a firm estimate.

Related Frigidaire washer codes

All Frigidaire washer codes
View all 100 Frigidaire washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass