Error code reference

Frigidaire Washer Error Codes

Q: How do I find the error code on my Frigidaire Washer?

Most Frigidaire washers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.

Q: What do I do if my code is not listed?

Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.

Q: Are these codes specific to my model?

The codes here apply broadly to Frigidaire washers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.

Q: How much does it cost to access the full diagnostic procedures?

A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.

101 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.

C9PCB failure.CLThe lid was opened for more than 20 minutes with Control Lock function activated.CLnIndicates the System Clean cycle has been entered to clean and freshen the washer…d:doDispenser door drDoor open E00Washer no error code E1Water fill time exceeds 60 minutes; water is not entering or entering slowly.E11Fill time too long-water tap closed, water flow rate too low, pressure sensor defective…E13Unexpected water loss-siphoning due to wrong drain pipe position or drain pump defective.E14Reed switch problem.E17Load out of balance during spin phase.E2Water drainage time exceeds 10 minutes; water is not draining.E21Water not pumping out fast enough-drain pipe blocked, drain pump defective, pressure…E23Drain pump relay on control board failed, wire off pump or pump defective.E24Drain pump relay on control board failed or wire off pump.E25Recirculation Pump Relay Sense failure.E26Recirculation Pump Relay failure.E3Lid is open during a cycle that requires the lid to be closed.E31Moisture sensor fault E32Washer pressure sensor calibration problems.E35Pressure sensor indicates water overfill-water inlet valve defective, air tube kinked, or…E36Console control board problem.E38Air chamber clogged or pressure sensor defective.E4The unit is out of balance during spin operation.E41Door is open when cycle starts E42Lid lock device failure-lid lock device defective or main control board defective.E43Console control board thinks the door locking device has failed.E44Washer lid closed sensing failure.E45Washer lid locked sensing failure.E46Washer lid lock command sensing failure.E47Console control board thinks the door PTC circuit is open in spin.E48Console control board thinks the door PTC circuit is closed.E49Washer lid incongruence between lid closed sensing and lid locked sensing.E4AWasher lid locked triac sensing failure on control board.E5Washer is not level; impact switch is being pressed by tub.E50Motor fault-an open circuit phase or rotor loses synchronization.E51Motor relay stuck open, locked rotor, harness fault, low power supply, thermal limiter-1…E52Tachometer signal missing from the drive motor.E53Motor fault E54Centrifugal Switch 2 stuck open/closed, heater open or shorted to ground, or Thermal…E55Motor sensing failure on main board E56Clutch jiggle failure-cannot execute the required motor jiggle.E57High current on inverter, MCE gate kill-IGBT module problem (short circuit of IGBT module…E58Washer high current on motor phase.E59Incongruence between real motor speed and expected motor speed; zero crossing error-power…E5AHigh temperature on heat sink on control board; DC bus voltage failure-DC bus voltage out…E5BLow voltage fault-the DC bus voltage has gone below 150 V.E5CVoltage too high on control board; over voltage fault-the DC bus voltage has gone above…E5DCommunication problem between main control board and motor control board.E5ECommunication problem between control board and speed control board.E5FCommunication problem between control board and speed control board.E61Heater relay failure E62Heating timeout E65High limit thermostat trip count too high E66Heating element relay failure.E67Heater sensing failure on main board E68Current leakage to ground on heater or fuse opened.E71NTC failure E72NTC failure E74Wash temperature does not increase.E75Better models only E76Better models only E81Program selector/encoder fault E82Key-stuck error E83Console control board problem.E91Communication error between the User Interface Board and the Main Control Board.E92Washer communication error between UI board and control board.E93Software configuration error E94Software configuration error E95Communication error.E97Software configuration error E98Console control board problem.E9BCommunication problem between microprocessor and external EEPROM.E9FCommunication protocol error.EA1Line frequency out of limits (54Hz<Lf<46Hz for 50Hz system or 64Hz<Lf<56Hz for 60Hz…EA2High line voltage EA3Low line voltage EA5Line amplitude sensing failure on main board EAEWasher line safe relay sensing failure.EB1Incoming power frequency out of limits.EB2Incoming line voltage above 130 VAC.EB3Incoming line voltage below 90 VAC.EBEConsole control board problem.EBFConsole control board problem.EC4Clutch cam error-cannot find the required cam position.EF1Washer clogged drain pump.EF2Too much suds causing overheating of motor; cannot reach target speed within estimated…EF5NTC temperature for the hot water valve over the limits.EF6Control reset.EF8Key stuck on console.ErrDisplayed when the cycle selector knob is turned to another selection after the cycle has…F01An internal fault in the control.F02A water temperature problem.F03Water supply issue F04The washer is not advancing through its increments.F05A problem with the keypad.F2PCB (main control board) failure.F8Water level sensor failure.FdLid lock failure.LOCControl Lock is engaged; displayed alternately with the estimated cycle time to indicate…PAUDisplayed as a reminder that the washer door is open and needs to be closed before the…

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for unlimited access to all brands and Max AI diagnostics.

More Frigidaire error codes

Common questions

How do I find the error code on my Frigidaire Washer?

Most Frigidaire washers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.

Are these codes specific to my model?

The codes here apply broadly to Frigidaire washers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.

What do I do if my code is not listed?

Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.

How much does it cost to access the full diagnostic procedures?

A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.