Error code reference

Frigidaire Dishwasher Error Codes

88 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.

CdClose dishwasher door CEMalfunction error code displayed when the dishwasher experiences a fault condition.CLDoor is open E:00No errors stored in memory.E:01Faulty pump relay on the power module.E:02Faulty heater relay on the power module.E:05Faulty water switch relay; water switch runs continually.E:06Door latch Hall sensor not detected; dishwasher won't run and Clean LED is flashing.E:08Heat pump detects low water level; dishwasher runs without heating.E:09Faulty heater circuit (open circuited) on the heat pump.E:11NTC or NTC wiring harness error; dishwasher not heating.E:13Incoming water too hot (>75°C / 167°F); dishwasher runs without heat pump heating element…E:15Float switch activated; water doesn't fill and drain pump runs continually/can't be…E:17Faulty water softener regeneration valve; water softener doesn't regenerate.E:20Faulty heat pump motor winding; wash cycle abruptly ends with Clean/Sanitized LEDs lit.E:21Heat pump is blocked/clogged.E:23Faulty drain pump.E:24Dishwasher won't drain; drain pump is blocked or drain hose obstruction.E:25Drain pump cover missing or loose, preventing pressure build-up; drain pump blocked.E:26Faulty water switch; water switch runs continually.E:27Under-voltage; low supply voltage to dishwasher.E:28Aqua sensor not properly calibrated; aqua sensor doesn't run during wash cycle.E:29Under/overvoltage condition on supply voltage.E:30Over-voltage; high supply voltage to dishwasher.ErMembrane switch failure; the control detects that any pad on the membrane switch has been…ER/CEConfiguration Error.ER/ERSwitch Failure.ER/uFFan not running.ER/uoVent will not close.HdIndicates a water heat delay HOIndicates a water heat delay (alternate display); the control is delaying the cycle to…hsThe control has sensed a problem with the Hall effect sensor in the wash motor.i00Low mains voltage detected i1Longer inlet time-faucet is not opened, water intake is restricted, or water pressure is…i10Water tap closed i11Water tap closed during dynamic filling i20Fails to drain i30Water detected from aqua control sensor i4Unit leaking-some element of the dishwasher is leaking.i41No pressure sensor signal i42Calibration invalid i43Pressure sensor signal too high i44Pressure sensor signal too low i45Calibration invalid i46Calibration invalid i51Asynchronous washing motor problem i52WP BLDC motor abnormal high current detected i53WP BLDC motor over current i54WP BLDC motor will not follow / rotor is locked i55DC Link overvoltage i56DC Link under voltage i57MCB Vbat voltage plausibility / ADC Fault i58WP motor plug connection detected wrong based on motor current measurements; also…i59WP current read ADC fault i5AOver temperature or overload i5BWP/DP current plausibility i5CDP BLDC motor abnormal high current detected i5DDP BLDC motor high current i5EDP BLDC motor will not follow / rotor is locked i5FDP motor plug connection detected wrong based on motor current measurements; also…i60Heating element problem i61Heating over temperature i70NTC sensor value out of range i80Auto door opener malfunction i81Auto door opener warning i91Checksum MCF i92Checksum CCF i93Checksum UIDATA i94UIDATA version mismatch i95UIDATA checksum mismatch iB0Turbidity sensor problem iC0User interface communication problem iC1MACS bus communication iC2ADSI communication iC3Communication between the power board and Motor Control Board does not start.iD0No tacho signal iD1Critical tacho signal iE0Flow controller position problem iF0Overfilling detected iF1High water level LORinse aid level is low; appears at end of cycle on models with a STATUS window indicating…OPTION LED's FlashingAll option LEDs flashing indicates a power failure has occurred.PFPower failure rAThe control has sensed a problem with the reed switch in the rinse aid dispenser.STATUS LED's FlashingThe STATUS LEDs that are lit when the door is opened will flash, indicating the door is…tuThe control has sensed a failure in the turbidity (soil) sensor while in the Water…uFIn the dry mode, the control does not receive proper feedback from the vent that the fan…uoThe control does not receive proper indication that the vent is closed; after 5 attempts…

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for unlimited access to all brands and Max AI diagnostics.

More Frigidaire error codes

Common questions

How do I find the error code on my Frigidaire Dishwasher?

Most Frigidaire dishwashers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.

Are these codes specific to my model?

The codes here apply broadly to Frigidaire dishwashers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.

What do I do if my code is not listed?

Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.

How much does it cost to access the full diagnostic procedures?

A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.