Skip to main content
Error code reference
Frigidaire Cooktop Error Codes
66 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
ECookware in the zone is the wrong size, off-center, or non-magnetic and cannot be…E10Center zone control defective key sensor.E11Center zone control defective key sensor.E12Center zone control key sensor defective.E14Right Rear zone control defective key sensor.E15Right Rear zone control defective key sensor.E16Right Rear zone control key sensor defective.E17Right Front zone control key sensor defective.E18Right Front zone control key sensor defective.E19Right Front zone control key sensor defective.E2Left Front zone control defective key sensor.E21Timer key sensor defective.E22Timer key sensor defective.E23Keep warm key sensor defective.E24Lock key sensor defective.E25Main power key sensor defective.E3Left Front zone control defective key sensor.E30AC input voltage too high at the 3 cook zones induction module.E31Internal generator error, sync in the 3 cook zones induction module / left side cooking…E32Low voltage output from 12V supply on filter board in the 3 cook zone induction module.E33Improper voltage output from filter board in the 3 cook zone induction module.E34Communication failure between filter board and power boards in the 3 cook zones induction…E35AC input voltage too low in the 3 cook zones induction module.E36Communication error between main touch control and filter board (3 cook zones induction…E37Heat sink temperature sensor break (3 zones induction module / left side cooking zones).E39Configuration mismatch between the User Interface and the induction module (occurs when…E4Left Front zone control key sensor defective.E40Communication failure between main touch control and filter board.E45Incoming power supply low voltage.E51Left Front element temperature sensor break.E52Left Rear element temperature sensor break.E53Center element temperature sensor break.E54Right Rear element temperature sensor break.E55Right Front element temperature sensor break.E6Left Rear zone control defective key sensor.E60Touch control general hardware error, keys.E61Left Front element temperature sensor too hot.E62Left Rear element temperature sensor too hot.E63Center element temperature sensor too hot.E64Right Rear element temperature sensor too hot.E65Right Front element temperature sensor too hot.E7Left Rear zone control defective key sensor.E70AC input voltage too high at the 3 cook zones induction module (same as E30).E71Internal generator error, sync (center cooking zone).E72Low voltage output from 12V supply on filter board in the 3 cook zone induction module…E73Improper voltage output from filter board in the 3 cook zone induction module (same as…E74Internal generator error, communication (3 zones induction module).E75AC input voltage too low in the 3 cook zones induction module (same as E35).E76Communication error in the 3 cook zones induction module for the center cooking zone.E77Heat sink temperature sensor break in the 3 cook zones induction module for the center…E8Left Rear zone control key sensor defective.E80Flash/ROM check fail (EEPROM data).E90AC input voltage too high in the 2 cook zones induction module.E91Internal generator error, sync in the 2 cook zones induction module.E9212V on the service section too low in the 2 cook zones induction module.E935V overcurrent on the switched 5V on the service section (2 zones induction module).E94Internal generator error, communication in the 2 cook zones induction module.E95AC input voltage too low in the 2 cook zones induction module.E96Communication error in the 2 cook zones induction module.E97Heat sink temperature sensor break in the 2 cook zones induction module.ErESEC error indicator displayed at power up or after a power failure if any surface…FElectronic oven control has detected a fault or error condition (generic F error code).HHot Surface warning indicating the cooking zone glass is still hot after the zone is…HEHot element indicator displayed after a cooking zone is turned OFF, indicating the…Prob ERRProbe error indicating the probe connector is not fully inserted into the receptacle, the…SFSabbath failure message displayed when power is restored after a power failure while the…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Frigidaire error codes
Common questions
How do I find the error code on my Frigidaire Cooktop?
Most Frigidaire cooktops show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Frigidaire cooktops. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.