Error code reference

Frigidaire Dryer Error Codes

Q: How do I find the error code on my Frigidaire Dryer?

Most Frigidaire dryers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.

Q: What do I do if my code is not listed?

Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.

Q: Are these codes specific to my model?

The codes here apply broadly to Frigidaire dryers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.

Q: How much does it cost to access the full diagnostic procedures?

A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.

71 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.

C9Communication error between control board and display board.E00No failure code experienced.E10General EEPROM fault-problem with communication between EEPROM and the microcontroller.E11Checksum error E12Non-fatal read/write error E21Water not pumping out fast enough (washer).E24Control NTC short circuit E25Control NTC open circuit E31Moisture sensor fault E32Contact Sensor frequency too low, caused by defective Electronic Control Board or foreign…E35Pressure sensor indicates water overfill (washer).E4Humidity sensor error E41Door open fault E42Door sensing failure E43Control board fails to lock lid (washer).E44Lid closed sensing failure (washer).E45Lid locked sensing failure (washer).E46Lid lock command sensing failure (washer).E49Lid incongruence between lid closed sensing and lid locked sensing (washer).E4AProgram timeout fault E5Outlet temperature sensor (NTC thermistor) error E51Motor relay stuck open, locked rotor, thermal limiter-1 open, motor centrifugal switch-1…E52Motor relay stuck closed / main board fault (rotary); motor fault E53Motor fault E54Centrifugal switch 2/heater/thermal limiter-2/wiring fault E55Motor sensing failure on main board E56Belt fault E57High current on inverter (washer).E58High current on motor phase (washer).E59Incongruence between real motor speed and expected motor speed (washer).E5AHigh temperature on heat sink on control board (washer).E5BHeater fault (no heating)E5CVoltage too high on control board (washer).E61Heater Relay failure; heater relay stuck open or closed, or wiring defective.E62Heating timeout E63Heater to earth ground E64Heater open circuit E65High Limit Thermostat trip count too high due to high vent restriction, defective High…E66Thermal Limiter Open Circuit E67Heater sensing failure on main board E68Key (button) stuck fault E71NTC failure E72NTC failure E73Inlet Control Thermistor open circuit E74Inlet Control Thermistor short circuit E75Valve NTC failure (washer).E81Program selector/encoder fault E82Key-stuck error E8CToo many trips in a period of time E91Communication error between Electronic Control Board and Interface Board (push button…E92Incompatible protocol E93Machine configuration checksum error due to wrong configuration data loaded, or defective…E94Cycle configuration checksum error due to wrong configuration data loaded or defective…E97Software configuration / program mismatch E9BExternal EEPROM Communication or Data Corruption due to defective Interface Board.EA1Line frequency out of limits (54Hz<Lf<46Hz for 50Hz system, 64Hz<Lf<56Hz for 60Hz…EA2High line voltage EA3Low line voltage EA4Improper home wiring EA5Line amplitude sensing failure on main board EAELine safe relay sensing failure (washer).EAFWatchdog reset EF1Check Exhaust Alarm due to high vent restriction, defective High Limit Thermostat, Inlet…EF3Max timeout timer EF4Check Exhaust Warning due to high vent restriction, defective High Limit Thermostat…EF8Key stuck F 01An internal fault in the electronic control board.F 02Control temperature sensor open or shorted.F 03No heat detected in the heating circuit.F 04The drying time has exceeded the program time for that cycle.F 05A problem with the keypad.

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for unlimited access to all brands and Max AI diagnostics.

More Frigidaire error codes

Common questions

How do I find the error code on my Frigidaire Dryer?

Most Frigidaire dryers show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.

Are these codes specific to my model?

The codes here apply broadly to Frigidaire dryers. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.

What do I do if my code is not listed?

Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.

How much does it cost to access the full diagnostic procedures?

A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.