mypros+
Error code reference

GE Refrigerator Error Code 0115

Odor remover fan feedback missing when the fan is running.

GE codesGE refrigerator codes

Odor remover fan feedback missing when the fan is running.

MyPros+ Max

Get the full diagnostic procedure for 0115.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0115 means on a GE refrigerator

Error code 0115 on a GE refrigerator indicates the control board commanded the odor remover fan to run but received no feedback signal confirming the fan is actually spinning. The control board monitors fan operation through a feedback circuit, typically a tachometer or Hall-effect signal. When the fan is energized but the expected feedback pulses are absent, the board logs this fault. The odor remover fan is a small motor-driven fan, separate from the evaporator and condenser fans, that circulates air through an activated carbon or similar odor-absorbing filter assembly.

For homeowners, this means the system designed to reduce food odors inside your refrigerator is not operating as intended. The fan that moves air through the odor filter has either stopped spinning or is not communicating its status back to the main control board. You may notice increased odors inside the refrigerator compartment, but the cooling function is typically not affected by this fault alone.

The root cause is usually a failed odor remover fan motor, a broken or disconnected wiring harness between the fan and the control board, or in less common cases, a control board output or feedback circuit failure. Inspecting the fan and its wiring connections is the logical first step before replacing components.

Source: manufacturer service documentation.

Common causes of 0115

  1. 01

    Failed odor remover fan motor

    Part replacement

    The fan motor itself has seized or burned out and cannot spin when energized, producing no feedback signal to the control board. This is the most common cause of this fault.

  2. 02

    Disconnected or damaged wiring harness to odor remover fan

    Wiring / connection

    The connector between the odor remover fan and the control board has come loose, corroded, or suffered wire damage, preventing the feedback signal from reaching the board even if the fan is functional.

  3. 03

    Obstructed fan blade

    Wiring / connection

    Debris, ice buildup, or a displaced component is physically blocking the fan blade from rotating, causing a stall condition that results in no feedback signal.

  4. 04

    Faulty main control board

    Part replacement

    If the fan motor and wiring both check out correctly, the control board's fan driver circuit or feedback input may have failed, causing it to incorrectly report missing feedback. This is the least likely cause.

See the test procedure for each cause

Frequently asked questions about 0115

What does error code 0115 mean on a GE refrigerator?
Code 0115 means the control board detected that the odor remover fan is not providing a feedback signal while it is supposed to be running. The board commands the fan to operate, but receives no confirmation that the fan is actually spinning. This points to a problem with the odor remover fan motor, its wiring, or a physical obstruction blocking the fan blade.
Can I still use my GE refrigerator with error code 0115 active?
Yes, in most cases your refrigerator will continue to cool normally with code 0115 active because the odor remover fan is not part of the primary cooling system. Food safety is generally not at risk from this fault alone. However, you may notice reduced odor control inside the compartment. The code should still be diagnosed and repaired to restore full function and prevent the fault from masking other developing issues.
How do I fix error code 0115 on a GE refrigerator?
Start by locating the odor remover fan, which is typically found inside the fresh food compartment near the odor filter housing. Check that the wiring connector is fully seated and that the wires show no visible damage. Next, check for any obstruction blocking the fan blade. If the wiring and blade are clear, the fan motor itself has likely failed and needs to be replaced. If a new fan motor does not resolve the code, the main control board may need evaluation.
How much does it cost to fix GE refrigerator error code 0115?
If the fix is a loose wiring connection or a simple obstruction, there is no parts cost. An odor remover fan motor replacement part typically runs between $30 and $80 depending on the GE model. If you hire a technician, expect a service call fee plus labor, which commonly brings the total to $100 to $200 for a fan motor replacement. A main control board replacement, if needed, is significantly more expensive, often $150 to $350 for the part alone.
Is error code 0115 on a GE refrigerator difficult to repair yourself?
Checking and reseating the wiring harness or clearing an obstruction from the fan blade is a low-difficulty repair that most homeowners can handle with basic tools. Replacing the odor remover fan motor is a moderate-difficulty task involving removing a panel or housing inside the compartment and unplugging and reconnecting a wiring harness. If you are comfortable with basic appliance disassembly, this is a reasonable DIY repair. Control board replacement is more involved and carries higher risk of secondary damage if done incorrectly, so professional service is advisable for that step.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass